Canadian Spa North American 60Hz Mode D'emploi page 15

Spa operation - Azure i262 CS Control Panel
Welcome To A New Dimension In Spa Control Systems.
Quick Start Guide - You can use your Smart Control two ways:
(1) Full Time Single Touch Button Control to turn a function On or
Off, like a Pump, Light, or Mood, without any navigation or additional
steps. (2) Navigation Mode where you utilize the full opportunities on
the Full Color Screen to Setup and Control your Spa. In Navigation
Mode, you can immediately return to the Home Screen by Touching
the Home Button, or automatically return to the Home Screen in a
few seconds.
This Section of the Control Panel User's Manual is intended to be a
Quick Start Guide to get you started in Navigating the Azure Plus i262
Control Panel Menu System.
Full Time System Control
This is the Home Screen with Canadian Spa Company Logo (Left)
These are the Full time System Control Touch Buttons that are always
active (Right)
At Any Time, all of the buttons Except the Select , Home , Left , Right ,
Up , and Down Navigation Buttons can be used to Directly Control the
Spa System equipment and other functions. The Icons on the bottom
of the Screen indicate that the Functions are turned On, or are Active.
The Pump 1 Button is the Jet Pump Control Button. In a 2 Pump
System, it is the Jet Pump 1 Control Button.
The Light
Button is the Spa Light Control Button.
The Temp
Button is the Water Temperature Control Button.
The Volume
Button is the Audio Volume Control Button.
The Option 2
Button Opens the Help Navigation Menu. In a 2
Pump System, it is the Jet Pump 2 Control Button.
The Option 3 Button Opens the Settings Navigation Menu. In a 2
Pump System, it is the Air Blower Control Button.
The Select Button Changes from the Home Screen to Navigation
Mode.
Navigation Mode System Control
The Settings Icon on the Navigation Screen is highlighted (Left)
These are the Navigation Mode Active Navigation Buttons.(Right)
In Navigation Mode, at the Center of the Screen, all of the Icon Func-
tions can be scrolled either Left or Right to access any of the Icon
Functions, with the Icons rotating like a wheel. All of the Following
Buttons can be used to Navigate and Select from the Menu System.
Owners Manual
The Up
Button Scrolls Up in the Menu Screens.
The Down
Button Scrolls Down in the Menu Screens.
The Left
Button Moves Left from Settings to the next Icon
Function Left, and Exits Back to the Previous Menu when you are in
a Menu.
The Right Button Moves Right from Settings to the next Icon
Function Right, and Moves Right to the Next Menu when you are in a
Menu.
The Select Button is used to Select a Menu Item, or turn an item
On or Off.
The Home
Button is used to Return to the Home Screen.
The Light , Temp
Option 3 Buttons continue to operate as the Full Time Spa Control
Buttons in Navigation Mode.
When Navigating the Menus, if the Yellow
Highlighted Menu Bar you are on has an
Arrow at the Right End of the Menu Bar,
use the Right Button to Navigate to the
Next Menu, and use the Left Button to Return to the Previous Menu.
Use the Up Button to Scroll Up to the next Menu Bar Above,
or use the Down Button to Scroll Down to the next Menu Bar Below.
If the Blue Area at the Bottom of the Menu
says More and has Arrows pointing Down
and/or Up, as indicated, use the Down
Button to Scroll from the Bottom Menu Bar
to the Next Menu, or the Up Button to Scroll from the Top Menu
Bar to the Previous Menu.
Powering Up Your Spa Control System
This Section of the User's Manual provides Detailed Instructions for
properly and Safely Powering Up your Spa Control System. Before
you turn ON the Power to your Spa Control System, make sure that
the Spa Water Level is at the Spa Manufacturer's Minimum required
Operating Water Level.
First turn ON the Branch Circuit Breaker Protecting the Spa and
Control System, and then turn ON the GFCI Protecting the Spa
and Control System.
It will take 3 to 4 minutes for the Software to Load and Control
System to Initialize. After the Power is ON, the Control Panel Button
Backlighting will turn ON, but the Display Screen will remain Black
for about 20 seconds. Then, for the next 20 seconds, there will be a
Screen that shows the Serial and Part Numbers. At about 40 seconds
after the Power is ON, there will be a Screen indicating that the
Software is Loading.
, Volume , Pump 1 , Pump 2
and