Yamaha QL5 Manuel De Référence page 283

s U76
This models a well-known vintage compressor/limiter used in a wide range of situations.
Parameter Range
INPUT –96.0 to 0.0 dB Input level
OUTPUT –96.0 to 0.0 dB Output level
Attack time of the compressor. Turning this all the way to the right
ATTACK 5.50 to 0.10 ms
produces the fastest attack.
Release time of the compressor. Turning this all the way to the right
RELEASE 1100.0 to 56.4 ms
produces the fastest release.
Switches the compression ratio. Pressing ALL produces the strongest
RATIO ALL, 4, 8, 12, 20
effect.
METER OFF, +4, +8, GR Switches the meter display
s Opt-2A
This processor emulates a well-known vintage model of vacuum tube opto compressor.
Parameter Range
GAIN –56.0 dB to 40.0 dB
PEAK REDUCTION –48.0 dB to 48.0 dB
RATIO 2.00 to 10.00
OUTPUT+10,
METER SELECT GAIN REDUCTION,
OUTPUT+4
s EQ-1A
This processor emulates a vintage EQ that's considered a classic example of a passive EQ.
Parameter Range
LOW FREQUENCY 20, 30, 60, 100 Hz
(LOW) BOOST 0.0 to 10.0
(LOW) ATTEN 0.0 to 10.0
HIGH FREQUENCY 3k, 4k, 5k, 8k, 10k, 12k, 16k Hz
(HIGH) BOOST 0.0 to 10.0
(HIGH) BAND WIDTH 0.0 to 10.0
(HIGH) ATTEN SEL 5k, 10k, 20k Hz
(HIGH) ATTEN 0.0 to 10.0
IN OFF, ON
Description
Description
Output level
Amount of gain reduction
Compression ratio
Switches the meter display
Description
Frequency range of the low range filter
Boost amount of the low range filter
Attenuation amount of the low range filter
Frequency range of the high range filter
Boost amount of the high range filter
Band width of the high range filter
Frequency range attenuated by the high range filter
Attenuation amount of the high range filter
Turns the processor on/off. If this is off, the filter section
will be bypassed, but the signal will pass through the
input/output transformers and the amp circuit.
s Dynamic EQ
This is a newly developed equalizer that dynamically changes the EQ gain in response to the
input signal, controlling the amount of EQ cut or boost in a way similar to a compressor or
expander.
Parameter Range
BAND ON/OFF OFF, ON
SIDECHAIN CUE OFF, ON
SIDECHAIN LISTEN OFF, ON
FILTER TYPE Low Shelf, Bell, Hi Shelf
FREQUENCY 20.0 to 20.0k Hz
Q 15.0 to 0.50
THRESHOLD –80.0 to 10.0 dB
RATIO ∞ : 1 to 1 : 1.50
MODE BELOW, ABOVE
ATTACK/RELEASE FAST, SLOW, AUTO
s Buss Comp 369
Parameter Range
INPUT ADJUST –15.0 to +15.0dB
LINK ON, OFF
METER IN, GR, OUT
VU IN, OUT
COMP IN ON, OFF
COMP RATIO 1.5:1, 2:1, 3:1, 4:1, 6:1
COMP GAIN 0.0 to +20.0dB
100ms, 400ms, 800ms
COMP RECOVERY
1500ms, a1, a2
COMP THRESHOLD –40 to –5 dBFS
LIMIT IN ON, OFF
LIMIT ATTACK FAST, SLOW
50ms, 100ms, 200ms
LIMIT RECOVERY
800ms, a1, a2
LIMIT THRESHOLD –16 to –5 dBFS
21
Description
Turns the corresponding band on/off
If this is on, the sidechain signal that controls the dynamics will
be sent to the CUE bus for monitoring.
If this is on, the sidechain signal that is linked to the dynamics
will be output to the bus (such as the STEREO bus or a MIX/
MATRIX bus) to which the inserted channel is being sent.
Switches the type of equalizer and sidechain filter
Frequency controlled by the equalizer and sidechain filter
Q of the equalizer and sidechain filter
Threshold value at which processing begins to apply
Sets the boost/cut ratio relative to the input signal
Specifies whether the processor will operate when the
sidechain signal exceeds the threshold setting (ABOVE) or
when it falls below the threshold setting (BELOW)
Attack time/release time for when compression or boost is
applied
Description
Input gain. However, the output gain is also linked so that there
is no change in the pass-through volume. For example, if
INPUT ADJUST is +5dB, the input gain is +5dB and the output
gain is –5dB.
Stereo link function (STEREO only)
Meter switch (STEREO only)
Meter switch (DUAL only)
Compressor on/off
Ratio of the compressor
Compressor gain
Compressor release. The release times for a1 (auto 1) and a2
(auto 2) change automatically. a1: Changes automatically
between 100 ms and 2 sec. a2: Changes automatically
between 50 ms and 5 sec.
Threshold of the compressor
Limiter on/off
Attack time of the limiter FAST: 2 ms, SLOW: 4 ms
Limiter release. The release times for a1 (auto 1) and a2 (auto
2) change automatically. a1: Changes automatically between
100 ms and 2 sec. a2: Changes automatically between 50 ms
and 5 sec.
Threshold of the limiter
Data List