Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8.2.2 Teach Function
8.2.2 Teach Function
1. In the programming menu, programme MPI
input 1 or MPI input 2 (MP.INP.1 / MP.INP.2)
1. In the programming menu, programme MPI
to TEACH
input 1 or MPI input 2 (MP.INP.1 / MP.INP.2)
input 1 or MPI input 2 (MP.INP.1 / MP.INP.2)
2. In operating mode, select the preset to be
t
to TEACH
changed: PRES1 or PRES2
2. In operating mode, select the preset to be
3. In operating mode, briefly activate MPI input 1
changed: PRES1 or PRES2
changed: PRES1 or PRES2
or MPI input 2 (NPN or PNP input logic)
3. In operating mode, briefly activate MPI input 1
or MPI input 2 (NPN or PNP input logic)
or MPI input 2 (NPN or PNP input logic)
the current count value will be adopted as
the new preset value
the current count value will be adopted as
the new preset value
See also 9. Error messages.
See also 9. Error messages.
The preset value can subsequently be
further modified via the keypad. If preset
The preset value can subsequently be
entry is inhibited (see note 8.2.1), then the
further modified via the keypad. If preset
Teach Function is also locked out.
entry is inhibited (see note 8.2.1), then the
Teach Function is also locked out.
8.2.3 Teach-In with tracking presets
8.2.3 Teach-In with tracking presets
If a tracking (trailing) preset (TRAIL or TR.AR) has
been programmed, the value for Preset 2 can be
If a tracking (trailing) preset (TRAIL or TR.AR) has
set either via the keypad or via the Teach-In
been programmed, the value for Preset 2 can be
function.
set either via the keypad or via the Teach-In
However the value for Preset 1 must be entered via
function.
the keypad. In this instance, it is not possible to use
However the value for Preset 1 must be entered via
the Teach-In function.
the keypad. In this instance, it is not possible to use
the Teach-In function.
With output operations ADD.BAT,
SUB.BAT, ADD.TOT, SUB.TOT, TRAIL
With output operations ADD.BAT,
and TR.AR, the Teach-In function is not
SUB.BAT, ADD.TOT, SUB.TOT, TRAIL
available for Preset 1.
and TR.AR, the Teach-In function is not
available for Preset 1.
8.3
Set Function
8.3
Set Function
The pulse counter and the timer can be set to a
value by means of the Set function.
The pulse counter and the timer can be set to a
value by means of the Set function.
1. In the programming menu, programme MPI
Input 1 or MPI Input 2 (MP.INP1 / MP.INP2) to
1. In the programming menu, programme MPI
SET
Input 1 or MPI Input 2 (MP.INP1 / MP.INP2)
Input 1 or MPI Input 2 (MP.INP1 / MP.INP2) to
2. In the programming menu, set the parameter
SET
t
SETPT to the desired value
2. In the programming menu, set the parameter
3. In operating mode, briefly activate MPI input 1
SETPT to the desired value
S
or MPI input 2 (NPN or PNP input logic)
3. In operating mode, briefly activate MPI input 1
or MPI input 2 (NPN or PNP input logic)
or MPI input 2 (NPN or PNP input logic)
For add. output operations the pulse
counter or timer will be set to the SETPT
Pulse counters and hour meters are
For add. output operations the pulse
value. For sub. output operations the
counter or timer will be set to the SETPT
preset to the SETPT value for adding
pulse counter or timer will be set to the
value. For sub. output operations the
output operations and to the difference
difference between the value of Preset 2
pulse counter or timer will be set to the
of preselection 2 and the SETPT value
and the value of SETPT
difference between the value of Preset 2
for subtracting output operations.
and the value of SETPT
See also 9. Error messages
See also 9. Error messages
Page 16
Page 16
8.4
Default Parameters
8.4
Default Parameters
Note: Three default parameter sets have
been permanently stored; these can be
Note: Three default parameter sets have
adapted as required. With each
been permanently stored; these can be
acknowledgment of the parameter sets, all
adapted as required. With each
parameters will be reset to the values
acknowledgment of the parameter sets, all
listed in the table.
parameters will be reset to the values
listed in the table.
8.4.1 Entry into the default setting
8.4.1 Entry into the default setting
Simultaneously press the UP key
and the DOWN key for 3 sec.
Simultaneously press the UP key
and the DOWN key for 3 sec.
The security prompt appears in
the display.
The security prompt appears in
the display.
Programming can be exited
again using the ENTER key.
Programming can be exited
again using the ENTER key.
Press the UP key or the DOWN
key to continue with the
Press the UP key or the DOWN
programming.
key to continue with the
programming.
The security prompt YES
appears in the display
The security prompt YES
appears in the display
Enter the default menu by
pressing the ENTER key
Enter the default menu by
pressing the ENTER key
The parameter set last
programmed appears in the
The parameter set last
display
programmed appears in the
display
8.4.2 Selecting the parameter sets
8.4.2 Selecting the parameter sets
The parameter sets are selected
using the UP key and the DOWN
The parameter sets are selected
key.
using the UP key and the DOWN
key.
Default parameter set 1
Default parameter set 1
Default parameter set 2
Default parameter set 2
Default parameter set 3
Default parameter set 3
8.4.3 Accepting the setting
8.4.3 Accepting the setting
Pressing the ENTER key accepts
the current setting and returns to
Pressing the ENTER key accepts
the operating mode.
the current setting and returns to
the operating mode.
The text SAVE is shown in the
display for 2 sec.
The text SAVE is shown in the
display for 2 sec.
Publicité
Chapitres
Table des Matières
