Low Power Mode (Eco Std - Standard Setting); Setting Of Washing Cycle Number Before "Clean" Message; Total Number Of Performed Washing Cycles; Software Release - TECO LR400 Manuel D'instructions

CAUTION
If the start and end time of the water heating system timing feature are set but the activation state is not set to oN, the timing feature will
have no effect on the water heating system.
CAUTION
If the wheel washer is turned off or the power supply to the wheel washer is interrupted, the internal watch will be reset and the water
heating system timing feature will be disabled.
The start and end time for the timing feature as well as the activation state will be kept, if they were previously set.
If the start and end time for the timing feature were previously set and the activation state was set to oN, setting the internal watch will
automatically resume the water heating system timing feature operation.

7.2. LoW PoWEr modE (ECo sTd - sTANdArd sETTINg)

The power absorbed by the wheel washer reaches 10 kW when the heater is active and the pump and/or electric motor are running.
The low power mode maintains the heater switched off when the pump is running. In this way, the power consumption absorbed by the wheel wa-
sher is reduced to 6 kW.
To set the low power mode, apply the following procedure:
• Keep depressed "RESET" + "DRY" buttons for 5 seconds.
• Press again the "DRY" button to enter in the low power mode page (second page).
• The upper line of the display shows the flashing message "LOW POWER".
• The bottom line of the display shows if the low power mode is "ON" or "OFF".
• Press the "30" button to enable or disable the low power mode.
CAUTION If the low power mode is activated, the fast warming procedure cannot be selected. For more details about the fast warming procedure,
refers to the paragraph "FAST WARMING PROCEDURE".
Note
If the operator selects the fast warming procedure when the low power mode is activated, on the display will appear for 5 seconds the message
"LOW POWER" , enabling the heater if not active.
The low power mode is normally disabled. The setting will remain memorized if the wheel washer is switched off. Otherwise, replacing or updating
the mother board, the setting will not remain memorized.

7.3. sETTINg oF WAshINg CYCLE NUmbEr bEForE "CLEAN" mEssAgE

The standard set number of the washing cycles before "CLEAN" message is 500. However, this number can be moved between 100 and 500,
according to the operator's needs.
To set the washing cycle number, apply the following procedure:
• Keep depressed "RESET" + "DRY" buttons for 5 seconds.
• Press 2 times the "DRY" button to enter in the setting of washing cycle number before "CLEAN" message page (third page).
• The upper line of the display shows the flashing message "WASHES TO CLEAN".
• The bottom line of the display shows the current washing cycle number before "CLEAN" message.
• Press the "30" button to increase of 10 the washing cycle number.
• Press the "60" button to decrease of 10 the washing cycle number.
• Press the "90" button to increase of 1 the washing cycle number.
• Press the "120" button to decrease of 1 the washing cycle number.
NOTE
- The maximum number of washing cycles is 500, whereas the minimum number is 100.

7.4. ToTAL NUmbEr oF PErFormEd WAshINg CYCLEs

This function shows the total number of washing cycles performed by the wheel washer. It is not possible to reset this number, not even replacing
the circuit board.
Apply the following procedure to display the total number of washing cycles:
• Keep depressed "RESET" + "DRY" buttons for 5 seconds.
• Press 3 times the "DRY" button to enter in the page (fourth page) displaying the total number of washing cycles performed by the wheel washer.
• The upper line of the display shows the message "WASHES".
• The bottom line of the display shows the current washing cycle number.

7.5. SOFTWARE RELEASE

This function shows the software version installed on the circuit board.
Apply the following procedure to display the software release:
• Keep depressed "RESET" + "DRY" buttons for 5 seconds.
• Press 4 times the "DRY" button to enter in the page (fifth page) displaying the software release.
• The upper line of the display shows the message "SOFTWARE RELEASE".
• The bottom line of the display shows the current software release.
NOTE
The software release is also shown during the wheel washer switch on phase.
44