Parameters Quick Guide - Siei QUIXDrive F Manuel D'instruction

Parameters quick guide

F menu: it sets and/or reads the frequencies that can be selected through the terminal board
C
D
ODE
ESCRIPTION
F - 0 0 F - 0 0 F - 0 0 Reference frequency 0
F - 0 0 F - 0 0
F - 0 1 F - 0 1 F - 0 1 F - 0 1 F - 0 1 Reference frequency 1
F - 0 2 F - 0 2
F - 0 2 F - 0 2 F - 0 2 Reference frequency 2
F - 0 3 F - 0 3 F - 0 3 Reference frequency3
F - 0 3 F - 0 3
F-04 /
/
F-05
F-06 /
F-07 /
F - 0 8 F - 0 8 Jogging frequency
F - 0 8 F - 0 8 F - 0 8
C menu:
it sets and executes some controls: to execute them, select value 7 and confirm via E.
C P
ODE ERFORMED ACTION
C - 0 0 C - 0 0 C - 0 0
C - 0 0 C - 0 0
Permanent storage of all parameters
Recall of previously stored parameters
C - 0 1 C - 0 1 C - 0 1
C - 0 1 C - 0 1
(the currently used parameters are replaced by the previously stored ones)
C - 0 2 C - 0 2 C - 0 2 C - 0 2 C - 0 2
Recall of the factory-set parameters (the storage depends on the operator's choice)
C - 0 3 C - 0 3 C - 0 3 C - 0 3 C - 0 3
Zero setting of the alarm memory
C - 0 4 C - 0 4
C - 0 4 C - 0 4 C - 0 4
Recall and storage of the parameters contained in the external programming key [from key to Inv.] (*)
C - 0 5 C - 0 5 C - 0 5
C - 0 5 C - 0 5
Storage of the inverter parameters on the external programming key [from Inv. to key]
C - 0 6 C - 0 6
C - 0 6 C - 0 6 C - 0 6
Measure of motor phase resistance and corresponding initialization of parameter P - 12 (page 25) (QUIX_V)(*)
(QUIX_V) : parameter available in the QUIXDrive_V version
Caution: all parameters or part of them can be write-protected through P - 19 parameter;
In case of a non-authorized modification attempt or with a running motor, the following message will be
displayed: Prot
NOTE: All parameters, which are not listed in the tables, are reserved for future developments; as a
consequence, they must be always set to 0.
P
ARAMETER VAL
P - 1 9 P - 1 9 P - 1 9
P - 1 9 P - 1 9 0 no protection
P - 1 9 P - 1 9 P - 1 9 P - 1 9 P - 1 9 1 F non-protected parameters, the others are protected
P - 1 9 P - 1 9 P - 1 9 P - 1 9 P - 1 9 2 all parameters are protected
P - 1 9 P - 1 9 P - 1 9
P - 1 9 P - 1 9 3 no protection; storage possibility with running motor too; not recommended
NOTE: The sign (*) means that the controls can not be executed with running motor
For safety reasons the P parameters, which can be changed, are divided into three groups or levels. Whether the parameters of
a given level (accessibility) can be changed or not depends on the presetting of the P-20 parameter:
P-20=1
P-20=2
P-20=3
Prot. . . . . Prot Prot Prot
P
ERFORMED ACTION
→
1st level (factory setting)
→
2nd level
→
3rd level
—————— QUIXDrive Inverter ——————
R U
ANGE NIT
0.0 / 480.0
0.1 Hz
" "
" "
" "
" "
" "
" "
" "
" "
INVERTER PARAMETERS
P P
RESET VALUE AGE
0.0
22
" "
"
" "
"
" "
"
1.0
24
(*)
(*)
(*)
17-GB