Accessories; Guarantee / Liability Exclusion; Disposal Notes - Multiplex RX-4/9 FLEXX M-LINK ID Notice D'utilisation

• If possible, carry out the range check when no other trans-
mitters are operating.
Carrying out the range check:
1. Select "range-check mode" on your transmitter, referring to
the operating instructions supplied with the M-LINK trans-
mitter or HFM3 M-LINK / HFM4 M-LINK / HFMx M-LINK 2.4
GHz RF module.
2. When checked with reduced transmitter power, the range of the
RX-4/9 or 4/16 FLEXX M-LINK ID receiver must be forty
metres. You have reached the range limit when the servos
start to move jerkily (in "steps").
There must be a line-of-sight connection between the trans-
mitter aerial and the receiver aerial (i.e. the model) when you
carry out the range check.
Hold the transmitter and receiver about one metre above the
ground for range checking.
If your transmitter features an automatic servo test facility,
we recommend that you activate it for one control function
(e.g. rudder). This sets up a steady movement of the servo,
and enables you to detect the limit of range clearly.
Important:
Carry out the initial range check with the motor switched off.
Hold the model in all possible attitudes, and attempt to
optimise reception by changing the position of the aerial.
For the second range check, run the motor at varying speeds
and check that the effective range is not significantly re-
duced. If there is a marked fall-off, locate and eliminate the
cause of the interference (the motor, the arrangement of the
receiving system and power supply components, vibration,
etc.).
12. A
CCESSORIES
MULTIPLEX PC USB adapter # 8 5149
for changing the SMART ID
MULTIPLEX Y-lead (UNI) # 8 5030
13. CE C
ONFORMITY
This device has been assessed and approved in ac-
cordance with European harmonised directives.
This means that you are the owner of a product whose design
and construction fulfil the protective aims of the European Com-
munity designed to ensure the safe operation of equipment.
The detailed CE conformity declaration can be downloaded in
the form of a PDF file from the Internet under www.multiplex-
rc.de. It is located in the DOWNLOADS area under PRODUCT
INFO.
14. D N
ISPOSAL OTES
Electrical equipment marked with the cancelled waste bin sym-
bol must not be discarded in the standard household waste;
instead it should be taken to a suitable specialist disposal
system.
In the countries of the EU (European Union) electrical equipment
must not be discarded via the normal domestic refuse system
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions for the
RX-4/9 FLEXX M-LINK ID and
RX-4/16 FLEXX M-LINK ID 2.4 GHz receivers
D
ECLARATION
(WEEE - Waste of Electrical and Electronic Equipment,
Directive 2002/96/EG). You can take unwanted equip-
ment to your nearest local authority waste collection
point or recycling centre, where the equipment will be
disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an impor-
tant contribution to the protection of our shared environment!
15. G / L
UARANTEE
The company MULTIPLEX Modellsport GmbH & Co.KG accepts
no liability of any kind for loss, damage or costs which are due to
the incorrect use and operation of this product, or which are con-
nected with such operation in any way. Unless the law expressly
states otherwise, the liability on the part of MULTIPLEX
Modellsport GmbH & Co.KG to pay damages, regardless of the
legal argument employed, is limited to the invoice value of those
products supplied by MULTIPLEX Modellsport GmbH & Co.KG
which were directly involved in the event in which the damage
occurred. This does not apply if unlimited liability is incurred
according to statutory law on account of intentional or gross neg-
ligence.
We guarantee our products in accordance with the currently
valid statutory regulations. If you wish to make a claim under
guarantee, your initial course of action should always be to con-
tact the dealer from whom you purchased the equipment.
The guarantee does not cover faults and malfunctions which are
caused by the following:
•
Incorrect or incompetent use
•
Maintenance carried out incorrectly, belatedly or not at all, or
not carried out by an authorised Service Centre
•
Incorrect connections
•
The use of accessories other than genuine MULTIPLEX
items
•
Modifications or repairs which were not carried out by
MULTIPLEX or by an authorised MULTIPLEX Service
Centre
•
Accidental or intentional damage
•
Defects due to normal wear and tear
•
Operation of the unit outside the limits stated in the
Specification, or in conjunction with equipment made by
other manufacturers.
E
IABILITY XCLUSION
Page 4/4