Bosch Active Line Notice Originale page 25

OBJ_BUCH-2616-002.book Page 9 Thursday, May 12, 2016 12:37 PM
After releasing the "+" button, the push assistance remains on
standby for another three seconds. Pressing the "+" button
again within this period will reactivate the push assistance.
Note: On some systems the push-assistance function can be
started directly by pressing the "WALK" button.
Note: The push assistance cannot be activated in the "OFF"
assistance level.
Switching bike lights on/off
In the model, in which the lighting is powered by the eBike
system, the front and rear light can be switched on and off at
the same time via the on-board computer with the button 6.
The illumination symbol s1 is displayed when the light is on.
Switching the bike light on and off has no effect on the back
lighting of the display.
eShift (optional)
eShift is the integration of automatic gear shifting systems in-
to the eBike system. You can configure the settings for the
"eShift" function under "My eBike". The gear or the cadence
is displayed in the "Ride", "Fitness" and "Map & Naviga-
tion" operating modes. If the field is not displayed, the user is
informed of changes by means of an indication on the display.
eShift mode is activated by holding down the "Home" button
12. It is only possible to activate eShift mode via the operating
unit 10. You can exit "eShift" mode again by repeatedly
pressing the "Home" button.
eShift with NuVinci H|Sync
The optimum gear for the respective speed is automatically
set according to a pre-defined desired cadence. In manual
mode you can choose between multiple gears.
In the "Cadence Control" mode, you can use the "–" or "+"
button on the operating unit to increase or decrease the re-
quired cadence. If you hold down the "–" or "+" button, the
cadence will increase or decrease in increments of five. The
desired cadence is shown on the display.
In the "Gear Control" mode, you can use the "–" or "+" but-
ton on the operating unit to switch back and forth between
several defined transmission ratios. The engaged gear is
shown on the display.
Under "Gear calibration", you can calibrate the continuously
variable transmission. Then follow the instructions on the dis-
play.
In the event of an error, it can also be necessary to perform
calibration when riding. Confirm the calibration here too, and
follow the instructions on the display.
Bosch eBike Systems
eShift with SRAM DD3 Pulse
The hub gear of the SRAM DD3 Pulse works on a speed-de-
pendent basis. Regardless of which gear is engaged on the de-
railleur gears, one of the three gears of the gear hub will auto-
matically be engaged.
It is also possible to use the "–" or "+" button to shift gear
manually here. Automatic mode is activated automatically if
you press the "–" button in first gear. If you press the "–" or
"+" button in automatic mode, the mode changes back to
manual mode. In automatic mode, only "A" is ever shown in
the gear display. If the gear is shifted in automatic mode, the
gear is not shown on the display.
If you are not in automatic mode, the engaged gear will be
shown briefly on the display whenever the gear of the hub
gear is shifted.
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
If the eBike is brought to a stop from a speed of more than
10 km/h, the system may automatically shift down a gear to a
set "Starting gear". The "Starting gear" can be set under
"My eBike"> "eShift (SRAM)".
eShift with Shimano Di2
For Shimano eShift you use the Shimano control lever to shift
gears.
The gear is always displayed in the eShift field. The gear is dis-
played briefly during a gear shift only when the eShift field is
not visible (e.g. in settings).
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
If the eBike is brought to a stop from a speed of more than
10 km/h, the system may automatically shift down a gear to a
set "Starting gear". The "Starting gear" can be set under
"My eBike"> "eShift (Shimano)".
English–9
1 270 020 XBN | (12.5.16)