Simmer; Melt; Bridge - Smeg SIMU524 Notice D'utilisation

6. After the third signal tone sounds, the Boiling Sensor
function automatically selects a lower power setting
to keep the water simmering.
7. While the water is simmering, you may add any ingredients
you like, set the timer and change the power setting.
NOTE: Changing the power setting or selecting the
Pause function during Boiling Sensor function will
cancel the function.
For Correct Operation of the Boiling Sensor Function:
Use water only (at room temperature).
■
Do not add salt, condiments or other ingredients until
■
the water reaches the boiling point.
Do not change the power setting of the surface cooking
■
area or remove or move the pot.
Fill the pot to at least 1/3 full (minimum of 1 qt [1 L]), and
■
do not fill the pot to the brim. See the following chart.
Do not use a pressure cooker on the surface cooking
■
area with the Boiling Sensor function selected.
For Optimum Results:
Do not use a lid on the pot being used in conjunction
■
with the Boiling Sensor function.
Do not activate the Boiling Sensor function if the surface
■
cooking area is already hot ("H" visible on display).
The quality of the pot used may have a bearing
■
on the Boiling Sensor function performance.
Important Information:
When the Bridge function is selected, the Performance
■
Boost and Boiling Sensor functions cannot be used.
If the Timer is set, it will be displayed alongside the
surface cooking area display.
The cooktop features automatic functions for each surface
■
cooking area. The available functions are shown next to the
selection keypad of each surface cooking area.
Each time an automatic function is selected, an indicator
■
light turns on next to the function and "A" appears in the
surface cooking area display.
The cooktop features automatic management of the use of
■
the Boiling Sensor and Performance Boost function settings;
therefore, in some cases it may not be possible to select
the Performance Boost function when the Boiling Sensor
function is selected on other surface cooking areas.
Surface Pot Base Diameter for
Cooking Area Use of Boiling Sensor
Diameter Function
7" (18 cm) 6 / " to 7
1
2
9 / " (24 cm) 9" to 9 /
1 4
2
11" (28 cm) 9" to 11" (24 to 28 cm)

Simmer

The Simmer function can be used on with all surface cooking
areas. Simmer can be used on more than 1 surface cooking
area at a time.
To Use:
1. Check that a surface cooking area has been selected.
2. Touch SIMMER. "A" will appear in the display,
and the indicator light next to Simmer will light.
The timer remains visible and can be set if desired.
Maximum
Amount of
Water in Pot
/ " (17 to 19 cm) 5 qts (4.7 L)
1
2
" (23 to 25 cm) 7 qts (6.6 L)
5
7 qts (6.6 L)
Simmer can be turned off in 2 different ways:
1. Use the power slider to set to a heat level.
2. Select a different cooking function.
WARNING
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
The Melt function can be used on with all surface cooking areas.
Melt can be used on more than 1 surface cooking area at a time.
To Use:
1. Check that a surface cooking area has been selected.
2. Touch MELT. "A" will appear in the display, and the indicator
light next to Melt will light.
The timer remains visible and can be set if desired.
Melt can be turned off in 2 different ways:
1. Use the power slider to set to a heat level.
2. Select a different cooking function.
B
A
A. Left side bridge
The Bridge function can be activated when surface cooking
areas are on or when they are off. The Bridge function allows
you to use 2 surface cooking areas as an extra-large surface
cooking area.
To Use:
1. Touch the Bridge keypad.
The indicator light above the Bridge keypad will light.
The heat setting levels for the 2 surface cooking areas
will default to "0" and can be set from a minimum of "1"
to a maximum of "9." Any timers that may be running for
the 2 surface cooking areas will turn off, and 2 dashes "--"
will appear in the Timer displays.
2. Slide the Heat Level slider to change the power level
up or down.
The selected heat level will show in the Heat Level display
for each surface cooking area in the Bridge function.
3. Touch the Bridge keypad when finished.
The surface cooking areas will resume operation as
2 separate areas.
NOTE: Performance Boost function cannot be used on
the same elements in combination with the Bridge function.
OR

Melt

OR

Bridge

7