Smeg SIMU524 Notice D'utilisation page 11

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate
Is the cooktop wired properly? See the Installation
■
Instructions for more information.
Has a household fuse blown, or has a circuit breaker
■
tripped? Replace the fuse or reset the circuit breaker.
If the problem continues, call an electrician.
Cooktop will not operate
Is the cooktop control set correctly? Touch the display
■
area on the control panel to select a cooking surface before
selecting a function.
Is the "Control Lock" Cooktop Lockout set? See "Control
■
Lock" section.
Has the cooktop turned off by itself? The Power keypad
■
was unintentionally touched. Touch POWER again. Reset
the cooktop.
Excessive heat around cookware on cooktop
Is the cookware the proper size? Use cookware about the
■
same size as the surface cooking area. Cookware should not
extend more than / " (1.3 cm) outside the cooking area.
1
2
Cooktop cooking results not what expected
Is the proper cookware being used?
■
See "Cookware" section.
Is the cooktop control set to the proper heat level?
■
See "Cooktop Controls" section.
Is the cooktop level? Level the cooktop. See the
■
Installation Instructions.
Display shows messages
Is the display flashing when you place a saucepan on an
■
induction surface cooking area? Check that the saucepan
is ferromagnetic. Check that the diameter of the saucepan is
large enough. Center the saucepan on the surface cooking
area. Allow the saucepan to cool down in the event that it
has become hot when used. Switch the surface cooking area
off, then on again. If the display still does not light up, turn
power off at the circuit breaker. Wait 20 seconds and turn
power back on.
Is the Performance Boost function display flashing and
■
switching off? The Performance Boost function operates
the surface cooking area with the most power. During long
cooking times, it is possible that the function will switch
the surface cooking area off to keep the cooktop from
overheating. You can continue to use the cooktop if the
display is not flashing.
TROUBLESHOOTING
■
■
Error Code
Cooktop
has turned
off and is
beeping every
10 seconds.
F42, F43
C81, C82, C83
F12, F21, F25,
F36, F37, F40,
F47, F56, F58,
560, F61, F62,
F63, F64
Operational cooktop sounds
■
■
■
Is the display flashing "Er" and numbers? If an "Er" and
a series of numbers appear in the display panel, turn power
off at the circuit breaker. Turn on again. If problem continues,
call customer service.
Is the display flashing "F" or "C" and numbers? If "F"
or "C" and a number are alternately flashing on the display,
refer to the following table for possible solutions.
Error
An object,
liquids or
soils are putting
pressure on the
control panel.
The power
voltage is too
low or too high.
The surface
cooking area
has overheated.
Is there a low humming? This occurs when cooking at
high power. The cause of this is the amount of energy that is
transmitted from the appliance to the cookware. This sound
will quiet or go away when the power is turned down.
Is there a crackling? This sound occurs when cookware is
used that consists of different materials. The noise is caused
by vibrations in the joint faces between the different layers.
It may change depending on the amount and type of food
being cooked.
Is there a fan noise? The electronics require a controlled
temperature in order to function reliably. The cooktop is
fitted with a fan that runs at various speeds according to the
temperature detected. The fan may also continue to run even
after the cooktop has been switched off, if the temperature it
detects is too high.
Solution
Thoroughly wipe or
remove any object
on touch keys.
Turn off the cooktop.
Wait 5 seconds, and
then turn it back on.
If this continues, contact
a qualified electrician.
The surface cooking area
automatic shutoff was
activated. Wait 5 minutes,
for it to cool down, and
then turn it back on.
Call customer service.
11