Safety Instructions; Loading The Tool - Stanley-Bostitch N66C Données Techniques

Table des Matières

Publicité

GB ©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.

SAFETY INSTRUCTIONS

F ©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
IMPORTANT READ CAREFULLY: It is important that all operators read and understand all sections of this
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
Tool Technical Data manual and the separate Safety and Operating Instruction Manual which come with this
tool. Failure to do so could result in you or others in the working area to be seriously injured.
D ©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined in
EN166 should be used. However all aspects of operators work, environment and other type/s of machinery
being used, should also be considered when selecting any personal protection equipment. Note: Non-side
NL ©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
shielded spectacles and face shields alone do not provide adequate protection.
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
WARNING! To prevent accidental injuries:
DK ©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
Never place a hand or any other part of the body in fastener discharge area of tool.
udgør ikke CE overholdelse for produkterne.
Never point tool at yourself or anyone whether it contains fasteners or not.
Never engage in horseplay.
SF ©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
Never pull the trigger unless the nose is directed towards the work.
Always handle the tool with care.
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
This tool is intended to be used for fastening wood to wood in pallet/crate and construction applications.
DO NOT USE for fastening harder materials which could cause buckling of the fasteners and damage to
G ©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
the tool. If you are unsure of the suitability of this tool for certain applications, please contact your local
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
sales office.
τα προϊόντα.
Do not pull the trigger or depress the trip mechanism whilst loading the tool.
To prevent accidental actuation and possible injury, always disconnect air supply.
I ©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use.
documento non garantiscono la conformità CE per i relativi prodotti.
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
Read the additional Safety & Operating instructions booklet before using tool.
Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
N ©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
dokumentet oppfyller ikke kravene for CE-merking for produktet.
IMPORTANT! Tool Operation:
P ©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
deste documento não estão em conformidade com a CE para os produtos.
To identify the operation type of your model, check the ID label affixed to the tool/ rear of this manual and the
corresponding table (marked ?) column L for that model. Read the corresponding section in the Safety & Operating
E ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
instructions for information of each trip type.
documento no suponen la conformidad con las normas CE de los productos.

LOADING THE TOOL

S ©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
1. Open the magazine: Pull down on the latch and swing the door open. Swing magazine cover open. (Fig. A)
documento no suponen la conformidad con las normas CE de los productos.
2. Check adjustment: the nailer must be set for the length of nail to be used. Nails will not feed smoothly if the
magazine is not correctly adjusted.
PL ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
To change the setting:
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
The magazine contains an adjustable nail platform on which the nail coil rests. The nail platform can be
adjusted up and down to several nail settings. To change settings, pull up on the post and twist to the correct
step. (Fig. B)
CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
dokumentu nie sú v súlade s CE pre dané výrobky.
HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
N66
- 30-40mm nails: 1
step
st
- 45-50mm nails: 2
step
nd
- 55-64mm nails: 3
step
rd
N75
- 38-40mm nails: 1
step
st
- 45-50mm nails: 2
step
nd
- 55-60mm nails: 3
step
rd
- 65-75mm nails: 4
step
th
GB

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

N75cN66c-1-eN66c-2-eN75c-1-eN75c-2-e

Table des Matières