Alarms Menu; Config Menu - Carrier HSM Manuel D'utilisation

4.9.5 - RUnTIMe menu
Point Description
hrhppmp Number of operating hours, external pump
hrhl1pmp Number of operating hours, loop 1
hrhl2pmp Number of operating hours, loop 2
hrdhwpmp Number of operating hours, DHW pump
hr_hp Number of operating hours, heat pump
hr_bckup Number of operating hours, back-up heating

4.9.6 - ALARMS menu

Item Description
ALRMMENU Alarm initialisation
4.9.6.1 - ALARMRST sub-menu
Point Description
RST_ALM Alarm reset
ALM Alarm status
alarm_1c Current alarm 1
alarm_2c Current alarm 2
alarm_3c Current alarm 3
alarm_4c Current alarm 4
alarm_5c Current alarm 5

4.9.7 - COnFIG menu

Item Description
GEN_CONF General configuration menu
PUMPCONF Pump configuration menu
HL1_CONF Configuration menu, loop 1
HL2_CONF Configuration menu, loop 2
DHW_CONF DHW configuration menu
BKUPCONF Back-up heating configuration menu
DIS_CONF District heating configuration menu
USERCONF User configuration menu
DATETIME Time control
DISPLAY Parameter display
CTRL_ID Control identification
FACTORY Factory parameters
4.9.7.1 - Gen_COnF sub-menu
Point Description
hp_add Heat pump CCN address
oat_add OAT sensor CCN address
hp_bias Heat pump correction control point 0.0 to 4.0
sani_dur Duration, anti-legionella treatment 0 to 120
sani_day Anti-legionella treatment days
sani_hr Anti-legionella treatment time
Notes Description
1 0 = Local sensor connected to the HSM
1 to 240 = CCN address of the heat pump, where the OAT is read
255 = No sensor
2 The logic board is rebooted after changing this parameter.
3
b7 b6 b5 b4
b7: Monday
b6: Tuesday
b5: Wednesday
b4: Thursday
b3: Friday
b2: Saturday
b1: Sunday
b0: Not used
4.9.7.2 - PUMPCOnF sub-menu
Point Description
hppmp_s External pump anti-stick function
hppmpsby Pump stop when heat pump is in standby No/Yes
hl1pmp_s Pump anti-stick function, loop 1
hl2pmp_s Pump anti-stick function, loop 2
dhwpmp_s DHW Pump anti-stick function
en
8
ENGLISH
Format
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
nnnnn
Format
Yes/No
nnn
nnn
nnn
nnn
nnn
Format Default
0 to 240 1
0 to 225 0
1
0.0
30
2
bbbbbbbb 10000000
0 to 23 12
b3 b2 b1 b0
Format Default Units
No/Yes Yes
No
No/Yes Yes
No/Yes Yes
No/Yes Yes
4.9.7.3 - HL1_COnF sub-menu
Point Description
Units
starttmr Time before pump start-up, loop
Hours
stop_tmr Time before pump stop, loop
Hours
oat_ctrl Control point based on outside air
Hours
temperature
Hours
curvpnt1 Climate curve: OAT point -36°C
Hours
curvpnt2 Climate curve: OAT point -27°C
Hours
curvpnt3 Climate curve: OAT point -18°C
curvpnt4 Climate curve: OAT point -9°C
curvpnt5 Climate curve: OAT point 0°C
curvpnt6 Climate curve: OAT point 9°C
curvpnt7 Climate curve: OAT point 18°C
curvpnt8 Climate curve: OAT point 27°C
Note Description
1 The logic board is rebooted after changing this parameter.
Units
-
-
4.9.7.4 - HL2_COnF sub-menu
-
Point Description
-
hl2_kp Mixing valve proportional gain
-
hl2_ki Mixing valve integral gain
-
hl2_bias Control point correction
-
Oat_ctrl Control point based on the outside
temperature
curvpnt1 Climate curve: OAT point -36°C
curvpnt2 Climate curve: OAT point -27°C
curvpnt3 Climate curve: OAT point -18°C
curvpnt4 Climate curve: OAT point -9°C
curvpnt5 Climate curve: OAT point 0°C
curvpnt6 Climate curve: OAT point 9°C
curvpnt7 Climate curve: OAT point 18°C
curvpnt8 Climate curve: OAT point 27°C
4.9.7.5 - BKUPCOnF sub-menu
Point Description
bck_pull Heat pump temperature pulldown time
hp_start Heat pump start-up time
htr_kp Electric heater proportional gain
htr_ki Electric heater integral gain
mix_kp Mixing valve proportional gain
mix_ki Mixing valve integral gain
Units
bck_fail Back-up for fault GT1
-
hl2_fail HL2 cmd for fault GT4
-
Note Description
^C
1 The logic board is rebooted after changing this parameter.
mn
-
3
-
4.9.7.6 - DHW_COnF sub-menu
Point Description
dhw_kp DHW proportional gain
dhw_ki DHW integral gain
dhw_dur Duration of DHW production
dhw_stop Duration of DHW production stop
Note Description
1 The logic board is rebooted after changing this parameter.
4.9.7.7 - DIS_COnF sub-menu
Point Description
d_hl_off Loop setpoint offset
d_hl_kp Heating heat exchanger proportional
gain
d_hl_ki Heating heat exchanger integral gain
d_dhw_kp DHW heat exchanger proportional gain -10.0 to 10.0 0.200
d_dhw_ki DHW heat exchanger integral gain
-
4.9.7.8 - USeRCOnF sub-menu
-
Point Description
-
language Language selection
-
use_pass User password
-
Note Description
1 0 = English
1 = Spanish
2 = French
3 = German
4 = Italian
5 = Translation
Format Default Units
1 to 300 300
1 1
1 to 300 120
1 1
No/Yes Yes
20.0 to 80.0 65.0
20.0 to 80.0 58.8
20.0 to 80.0 52.5
20.0 to 80.0 46.3
20.0 to 80.0 40.0
20.0 to 80.0 33.3
20.0 to 80.0 26.7
20.0 to 80.0 26.7
Format Default Units
-10.0 to 10.0 0.500
-10.0 to 10.0 0.050
-9.0 to 9.0 0.0
No/Yes Yes
20.0 to 80.0 65.0
20.0 to 80.0 58.8
20.0 to 80.0 52.5
20.0 to 80.0 46.3
20.0 to 80.0 40.0
20.0 to 80.0 33.3
20.0 to 80.0 26.7
20.0 to 80.0 26.7
Format Default Units
0 to 60 60
1
0 to 10 5
1
-10.0 to 10.0 0.200
-10.0 to 10.0 0.020
-10.0 to 10.0 0.200
-10.0 to 10.0 0.020
0 to 100 30
0 to 100 30
Format Default Units
-10.0 to 10.0 0.500
-10.0 to 10.0 0.050
15 to 120 60
1
15 to 60 15
1
Format Default Units
0.0 to 10.0 2.0
-10.0 to 10.0 0.200
-10.0 to 10.0 0.020
-10.0 to 10.0 0.020
Format Default Units
0 to 5 0
1
1 to 9999 11
mn
mn
-
°C
°C
°C
°C
°C
°C
°C
°C
-
-
^C
-
°C
°C
°C
°C
°C
°C
°C
°C
mn
mn
-
-
-
-
%
%
-
-
min
min
^C
-
-
-
-
-
-