Friedrich QuietMaster SS Instructions D'installation page 6

FIGURE E
STEP 9 STEP 9 STEP 9 STEP 9 STEP 9 CUT WINGBO CUT WINGBOARD P CUT WINGBO CUT WINGBO CUT WINGBO
#8) to fit the spaces between the side window channels and the sides of the cabinet.
(See Figure E.)
NOTE: NOTE: NOTE: NOTE: NOTE: AFTER CUTTING THE PANELS, MAKE A TRIAL TEST TO SEE IF THEY FIT THE SP AFTER CUTTING THE P AFTER CUTTING THE P AFTER CUTTING THE P AFTER CUTTING THE P
BEFORE GOING TO STEP 10. BEFORE GOING TO STEP 10. BEFORE GOING TO STEP 10. BEFORE GOING TO STEP 10. BEFORE GOING TO STEP 10.
STEP 10 STEP 10 STEP 10 STEP 10 STEP 10 ASSEMBLE THE CLIPS TO THE WINGBO ASSEMBLE THE CLIPS TO THE WINGBO ASSEMBLE THE CLIPS TO THE WINGBOARD P ASSEMBLE THE CLIPS TO THE WINGBO ASSEMBLE THE CLIPS TO THE WINGBO
steel clips (Item 10) to the edges of the cut wingboard panels (See Figure F.)
FIGURE F
CUT WINGBOARD
PANEL
CENTER THE HOLE IN THE
SPEED NUT OVER THE SLOT
IN THE WINGBOARD PANEL
STEP 11 STEP 11 INST INST ALL THE SIDE WINGBO ALL THE SIDE WINGBO
STEP 11 STEP 11 STEP 11 INST INSTALL THE SIDE WINGBO INST ALL THE SIDE WINGBOARD P ALL THE SIDE WINGBO
that the outside support brackets have been installed as shown in Figures C and D on Page 4. Raise
the window sash and install the right and left side wingboard panels. (See Figure G, Page 7.)
STEP 12 STEP 12 INST INST ALL THE WINDOW SEALING GASKETS: ALL THE WINDOW SEALING GASKETS:
STEP 12 STEP 12 STEP 12 INSTALL THE WINDOW SEALING GASKETS: INST INST ALL THE WINDOW SEALING GASKETS: ALL THE WINDOW SEALING GASKETS: Measure and cut the vinyl window seal gasket (grey color,
Item # 12) to fit the width of the window, and install as shown in Figure H on Page 7. Pull the window
sash down behind the gasket. Measure and cut the dark foam window seal gasket (Item #13) and
install it between the upper glass panel and the top part of the lower sash. (See Figure H, Page 7).
NOTE: NOTE: NOTE: FOR REASONS OF SECURITY AND SAFETY FOR REASONS OF SECURITY AND SAFETY, THE CUSTOMER MUST PRO FOR REASONS OF SECURITY AND SAFETY
NOTE: NOTE: FOR REASONS OF SECURITY AND SAFETY FOR REASONS OF SECURITY AND SAFETY
MEANS OF PREVENTING THE WINDOW FROM OPENING. MEANS OF PREVENTING THE WINDOW FROM OPENING. MEANS OF PREVENTING THE WINDOW FROM OPENING. MEANS OF PREVENTING THE WINDOW FROM OPENING. MEANS OF PREVENTING THE WINDOW FROM OPENING.
Page 6
ARD P ARD PANELS: ARD P ARD P ANELS: Measure and cut the wingboard panels from the Masonite supplied (Item ANELS: ANELS: ANELS:
ANELS, MAKE A TRIAL TEST TO SEE IF THEY FIT THE SPA A A A A CE WITH ABOUT 1/8" CLEARANCE ANELS, MAKE A TRIAL TEST TO SEE IF THEY FIT THE SP ANELS, MAKE A TRIAL TEST TO SEE IF THEY FIT THE SP ANELS, MAKE A TRIAL TEST TO SEE IF THEY FIT THE SP
ARD P ARD P ARD PANELS: ARD P
"J" TYPE SPEED NUT (ITEM #9) 2
REQUIRED
ARD P ARD P ANELS: ANELS:
ARD P ARD PANELS: ANELS: Be sure the cabinet has been secured to the window sill and ANELS:
MEASURE DISTANCE "B" TO INSIDE OF THE
CHANNEL ON EACH SIDE
CUT HERE AND DISCARD CENTER WASTE
MATERIAL.
WINGBOARD
SUBTRACT 1/8" FROM DIMENSION "B" AND
MEASURE FROM THE EDGE OF THE
WINGBOARD (ITEM # 8), MARK, AND CUT
WITH A SAW
ANELS: ANELS: ANELS: Assemble the "J" type speed nuts (Item 9) and spring ANELS:
SPRING STEEL CLIP
(ITEM #10) 2 REQUIRED
3"
CUT EDGE
3"
SLIDE CLIP OVER CUT EDGE
OF WINGBOARD PANEL
, THE CUSTOMER MUST PRO , THE CUSTOMER MUST PRO , THE CUSTOMER MUST PROVIDE A
, THE CUSTOMER MUST PRO
CE WITH ABOUT 1/8" CLEARANCE CE WITH ABOUT 1/8" CLEARANCE CE WITH ABOUT 1/8" CLEARANCE CE WITH ABOUT 1/8" CLEARANCE
VIDE A VIDE A VIDE A
VIDE A