Installation Instructions For Remote Blower; Installation Instructions For 2-Piece Tubs With Whisper+ Technology™ Or Heated Soak - Jacuzzi Amalia 59 Instructions D'utilisation

Freestanding Baths

Installation Instructions for Remote Blower

For ease of installation of remote blower and air line fittings, it is recommended there be access to the underside of the bathtub,
either from above or below the sub floor.
Determine the locations for the blower and verify that access to blower and airline fittings will be possible after bathtub is
1 1
installed. Blower location must be within 10 feet of the tub with no more than three elbows as illustrated (Fig. 6).
Use 1-1/2" schedule 40 PVC to connect the bathtub to the blower. Pipe connected directly to the blower should be secured
2
with a stainless steel screw. Do not glue blower to the PVC.
3
The control cable provided with the tub is 25' long. Do not wrap the cable along the pipe from blower to bathtub.
4
Once airline fittings and control cable are connected to the blower, plug the blower into the outlet and test the operation
before completing the installation.
Installation Instructions for 2-Piece Tubs Equipped with Whisper+ Technology™ or
Heated Soak
1
After locating the drain alignment kit, electrical, and water supply lines
with the supplied template (Modena™ only), use a marker to trace
the inside footprint of the skirt in the location where the bathtub will be
placed. Add silicone only to the bottom of the skirt and place back in
the marked area (Fig. 7).
2
Install the overflow drain kit onto the bathtub with the supplied brass
tailpiece that is included in the drain alignment kit (Modena™ only). Be
sure to apply the supplied grease to the end of the tailpiece where it
will connect to the drain alignment kit (Fig. 9).
Place (2) four foot long 2" x 4" wood supports across the top of the
3
skirt. Position the wood supports evenly over the skirt as illustrated
(Fig. 8). They will support the bathtub during the connection of the
water supply lines and the electrical connection.
4 Place the bathtub onto the wood supports in the position that it will be
lowered into the skirt (Fig. 9). The wood supports need to be positioned
under the bathtub away from the foam blocks or adjustable brackets.
Orient the bathtub properly with respect to the electrical outlet and the
drain. Also, make sure the drain and overflow areas line up with the
drain alignment kit.
Connect the flexible water supply lines to the faucets if using a deck
5
mounted faucet. Make certain the valves are in the closed position.
Turn on the water supply and check for leaks at all connections.
6
Connect the electrical plug to the dedicated GFCI-protected outlet.
Position Bathtub into Skirt
Lower the bathtub into place. Three people will be required to lower the
1
bathtub into the skirt (one person at each end to lift the bathtub, and
the third person to remove the two wood supports from the top of the
bathtub skirt).
Take care not to damage the brass tailpiece while lowering the bathtub
into the skirt (Modena™ only).
Turn on power to the dedicated GFCI-protected circuit and check
2
vsystem operations.
Installation Instructions
Fig. 5
Fig. 6
PLUMBING CONNECTION
FROM TUB
4" HOLE
Figure 6
Figure 7
Figure 8
Electrical
(28" Cord
Included)
www.jacuzzi.com
4" HOLE
Apply Silicone
Fig. 7
2" x 4" Wood
Supports
Fig. 8
Fig. 9
Apply
Grease
(Drain
Alignment
Drain
Kit Only)
Alignment Kit
(Modena™ Only)
Faucet Location
(If Applicable)
36" Stainless Steel
Supply Lines
(If Applicable)
Page 7