Memory Storage Of Lc/Rc Radio Controls; Deletion Of Radio Codes; Obstacle Detection Sensitivity - FAAC E604 Mode D'emploi

• Put the two radio controls frontally into contact.
On the memory stored radio control, press and hold down the push-button relating to the channel you wish to
•
transfer - the radio control LED lights up on steady beam.
• On the radio control to be memory stored, press the required push-button and release it after the radio control has
flashed twice.
• To finish programming, press twice in close succession, the push-button of the memory stored radio control.
The automated system will perform an opening manoeuvre - make sure that there are no obstacles inside the
operating range.

8.3. Memory storage of LC/RC radio controls

You can memory store up to a maximum of 250 codes, subdivided between the two channels, OPEN and
OPEN/CLOSE.
1. Use LC/RC remote controls only with receiver module at 433 MHz.
2. On the control unit, press the push-button of the channel you wish to memory store, P2 for the OPEN channel or
P3 for the OPEN/CLOSE channel.
3. The relevant LED on the control unit begins to flash - release the push-button.
4. On the radio control, press the push-button with which you wish to associate the selected channel.
5. The LED on the control unit lights up on steady beam for about one second, signalling that the radio control was
stored in the memory, then it resumes flashing.
6. During this stage further radio controls can be stored in the memory.
7. After about 10 seconds, the control unit automatically exits the learning stage.
8. To add other radio controls or memory store the second channel, repeat the operations from point 1
8.3.1. r
emote memory storAge oF
Other radio controls can be remotely stored only with the LC/RC radio controls, i.e. without using the push-buttons of
the control unit,, but using a previously stored radio control.
1. Get a radio control already memory stored on one of the 2 channels.
2. Step near to the automated system.
3. Press and hold down push-buttons P1 and P2 (see radio control instructions) simultaneously for about 5 seconds.
4. Within 5 seconds, press, on the memory stored radio control , the push-button you wish to transfer to the new
radio control. In this way the learning stage on the selected channel is activated on the control unit.
5. Within 5 seconds, press, on the new radio control, the push-button you wish to associate with the selected
channel.
6. After the new radio control has been stored in the memory, the control unit keeps the learning mode active on
the selected channel for about 5 seconds.
7. During these 5 seconds, other radio controls can be memory stored on the control unit, as ever associated with
the activated channel.
8. When 5 seconds have elapsed from memory-storage of the last radio control, the control unit automatically
exits the learning stage.
9. To check if the radio control was correctly memory stored, wait for 5 seconds after sending the code.

8.4. Deletion of radio codes

To delete all the radio controls stored in the memory, go through the following procedure:
1. Press and hold down one of the two push-buttons P2 or P3.
2. The relevant LED begins to flash.
3. After five seconds, the LED starts to flash at high speed.
4. After another five seconds both LEDS, DL6 and DL7 light up on steady beam.
5. Release the push-button.
This operation is irreversible, and all radio controls associated with both the OPEN and the OPEN/CLOSE
command will be deleted.
The obstacle detection device enables the control unit to detect any obstacles while the beam is moving. As this is
an electronic device, it stays constant through time and is not subject to variations - this guarantees an automated
system with a constant safety level.
By using the TR1 trimmer, you can increase or reduce the obstacle detection sensitivity. Turn the trimmer clockwise to
increase detection sensitivity, vice-versa turn it anti-clockwise to reduce obstacle detection sensitivity.
This device is active both during the beam closing stage and during the beam opening stage.
If it operates during the opening stage, it stops the operation of the automated system and reverses motion for 1
second. At this point, a pulse must be sent to the control unit, to resume normal programmed operation.
If it operates during the closing stage, it reverses operation until the automated system is completely open without
disabling any automatic closing.
If it operates three times in succession, it blocks the operation of the automated system and locates itself in stop
position, disabling automatic closing, if it was activated. To restore normal operation, you must command the beam
to open or close. Behaviour patterns will differ, according to the command sent:
OPEN or OPEN/CLOSE pulse: In this case, the beam starts an opening manoeuvre at slower speed until the beam is
completely open. When complete opening has been reached, the beam resumes its normal operating cycle,
re-activating automatic re-closing, if it had been enabled.
CLOSE pulse: In this case, the beam starts a closing manoeuvre at slower speed until the beam is completely closed.
When closed, the beam resumes its normal operating cycle, re-activating automatic re-closing, if it had been
enabled.
lc/rc
rAdio controls

9. OBSTACLE DETECTION SENSITIVITY

7