Technical Data; Ambient Conditions; Btl7-A; Btl7-C - Balluff BTL7-A -M Série Mode D'emploi

BTL7-A/C/E/G_ _ _-M_ _ _ _-A/B/Y/Z(8)-S32/S115/S135/KA_ _
Micropulse Transducer - Rod Style
11

Technical data

11.1 Accuracy
The specifications are typical values for BTL7-A/C/E/G... at
24 V DC and room temperature, with a nominal length of
500 mm in conjunction with the BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R, BTL-P-1014-2R or
BTL-P-0814-GR-PAF magnet.
The BTL is fully operational immediately, with full accuracy
after warm-up.
For special versions, other technical data may
apply.
Special versions are indicated by the suffix -SA
on the part label.
Repeat accuracy
Voltage, typical
Current, typical
Sampling rate
Dependent on nominal length
At nominal length = 500 mm
Non-linearity at
Nominal length ≤ 500 mm
Nominal length > 500 to
≤ 5500 mm
Nominal length > 5500 mm
Temperature coefficient
(nominal length = 500 mm, magnet in
the middle of the measuring range)
Max. detectable speed
11.2

Ambient conditions

Operating temperature
Storage temperature
Relative humidity
Outer rod pressure rating
(when installed in hydraulic
cylinders)
For Ø 8 mm
For Ø 10.2 mm
Shock rating
per EN 60068-2-27
1)
Continuous shock
per EN 60068-2-29
1)
Vibration
per EN 60068-2-6
1)
Degree of protection per
IEC 60529
Connector S32/S115/
S135 (when attached)
Cable KA_ _
Individual specifications as per Balluff factory standard
1)
www.balluff.com
±10 µm
±5 µm
250 µs to 5.5 ms
500 µs
±50 µm
±0.01% FS
±0.02% FS
≤ 30 ppm/K
10 m/s
-40°C to +85°C
-40°C to +100°C
< 90%, non-condensing
< 250 bar
< 600 bar
150 g/6 ms
150 g/2 ms
20 g, 10 to 2000 Hz
IP67
IP68
1)
11.3 Supply voltage (external)
Voltage, stabilized:
BTL7-_1_ _-...
BTL7-_5_ _-...
Ripple
Current draw (at 24 V DC)
Inrush current
Reverse polarity protection
Overvoltage protection
Dielectric strength
(GND to housing)
11.4 Output
BTL7-A... Output voltage
Load current
BTL7-C... Output current
Load resistance
BTL7-E... Output current
Load resistance
BTL7-G... Output voltage
Load current
Short circuit resistance
11.5 Input
Programming inputs La, Lb:
BTL7-_1_ _-...
BTL7-_5_ _-...
Overvoltage protection
20 to 28 V DC
10 to 30 V DC
≤ 0.5 V
ss
≤ 150 mA
≤ 500 mA/10 ms
Up to 36 V
Up to 36 V
500 V AC
0 to 10 V and 10 to 0 V
≤ 5 mA
0 to 20 mA/20 to 0 mA
≤ 500 ohms
4 to 20 mA/20 to 4 mA
≤ 500 ohms
-10 to 10 V and 10 to -10 V
≤ 5 mA
Signal cable to 36 V
Signal cable to GND
High-active
20 to 28 V DC
10 to 30 V DC
up to 36 V
english 21