Technical Data; Dimensions, Weights, Ambient Conditions; Supply Voltage (External); Outputs - Balluff BTL5-A/C/E/G1 M/U K-SR 32/K Serie Notice D'utilisation

BTL5-A/C/E/G1_-M/U_ _ _ _-K-SR 32/K_ _
Micropulse Linear Transducer - Rod Style
6

Technical Data

Typical values at DC 24 V and 25 °C. Ready for operation at once, full accuracy after warm-up. With magnet
BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R:
Resolution + hysteresis
= repeatability
Voltage 0.3 mV
Current 0.6 µA
Minimum 5 µm
Sampling rate:
Nom. length f
Standard
< 2000 mm 1 kHz
> 2000 mm 0.5 kHz
Non-linearity
Nom. length < 500 mm > 500 mm
in µm ±100 ±0,02 % FS
Temperature coefficient
Voltage output:
[150 µV/K + (5 ppm/K * P * V/NL)] * ∆T
Current output:
[0,6 µA/K + (10 ppm/K * P * I/NL)] * ∆T
V = output voltage range in [V]
I = output current range in [mA]
NL = nominal length in [mm]
∆T = temperature coefficient in [K]
P = magnet position in [mm]
Shock loading 100 g/6 ms
per IEC 68-2-27 1
Continuous shock 100 g/2 ms
per IEC 68-2-29 1
Vibration 12 g, 10 bis 2000 Hz
per IEC 68-2-6 1
(take care to avoid inherent reso-
nances of protective tube)
Pressure up to 600 bar
when installed in a
hydraulic cylinder
1 Individual specifications as per
Balluff factory standard
7

Versions (indicated on product label)

Supply voltage: 1 = DC 24 V
BTL5-A11-M0450-K-SR 32
Nom. length (4 digits): M= metric in mm
Analog interface:
Voltage output
Current output C10 = 0 ... 20 mA
8
english
6.1 Dimensions, weights,
ambient conditions
Nominal length
Dimensions
Weight
Housing
Pressure tube Stainless steel 1.4571
diameter
wall thickness
e-modulus
Mounting
6 socket head cap screws,
ISO 4762 M6 x 16 - A2-70
Operating temp.
Humidity
Protection rating per IEC 529
with connector attached:
connector version IP 67
cable version
(type tested at 5 bar / 48 h)
6.2

Supply voltage (external)

Regulated supply voltage
BTL5-_1...
Ripple
Current draw
Inrush
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing
Electr. connection, SR 32: with connector,
K05: with 5 m cable
Rod style,
Mounting: 6 screws ISO 4762 M6 x 16 - A2-70
U = inches in 1/10 Inch
A11 = 10 ... 0 V and 0 ... 10 V
G11 = 10 ... –10 V and –10 ... 10 V
E10 = 4 ... 20 mA
C17 = 20 ... 0 mA E17 = 20 ... 4 mA
6.3
BTL5-A11...
< 4000 mm Output voltage
➥ ➥ ➥ ➥ ➥ Fig. 3-2
Load current
ca. 2 kg/m Ripple
Stainless steel BTL5-G11...
Output voltage–10...10/10... –10 V
10.2 mm Load current
2 mm Ripple
ca. 200 kN/mm 2 BTL5-C1_...
Output current 0...20/20...0 mA
Load resistance
BTL5-E1_...
–40 °C to +85 °C Output current 4...20/20...4 mA
< 90 %, non-dewing Load resistance
6.4
Analog interface
IP 68
for shielded cable (max. length, see
Wiring), Ø 6 to 8 mm
6.5
Transducer
DC 20 to 28 V
< 0.5 V
pp
6.6
< 150 mA
< 3 A/0.5 ms
Magnets BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R
Dimensions
Weight
500 V
Housing
Operating temp.
Magnets BTL5-P-4500-1
(Electromagnet)
Weight
Housing
Operating temp.
6.7
Connectors

Outputs

0...10/10...0 V
< 5 mA
< 5 mV
< 5 mA
< 5 mV
< 500 Ohm
< 500 Ohm

Connection to processor

Included in shipment

➥ ➥ ➥ ➥ ➥ Fig. 3-2

Magnets

(order separately)

➥ ➥ ➥ ➥ ➥ Fig. 3-4
approx. 10 g
anodized aluminum
–40 °C to +85 °C
approx. 90 g
plastic
–40 °C to +60 °C

Accessories (optional)

➥ ➥ ➥ ➥ ➥ Fig. 4-3