Changing The Tuning Method (Stretch Tuning); Changing How The Pedals Work; Specifying How The Bass Part Behaves (Leading Bass); Chord Recognition When Split Is On - Roland RP401R Mode D'emploi

Display Value
F08
1 , 2
1 (Sostenuto, Soft),
F0g 2 (Start/Stop),
3 (Intro/Ending),
4 (Variation),
F10
5 (Fill-in),
6 (Leading Bass)
F11
Off , On
1 (Intelligent),
F12
2 (Standard)
F13
Off , On
U.01 – U.10
(USER 01–10)
F14
N.01 – N.gg
(USB 01–99)
F15
None
F16
None
F17
000 – ggg
Explanation
Changing the Tuning Method
This setting changes the type of stretch tuning, a tuning method that is used specifically for pianos, in which the high notes are tuned
slightly sharper and the low notes are tuned slightly flatter.
Normally, you should use the "1" setting (standard tuning curve).

Changing How the Pedals Work

Here you can assign the functions of the center pedal ( F0g ) and left pedal ( F10 ).
1 " Sostenuto pedal ( F0g ), soft pedal ( F10 )
2 " Same function as the [s (Start/Stop)] button
3 " Intro/Ending function on/off (same function as the [y(Intro/Ending)] button)
4 " Variation on/off (same function as the [x (Variation)] button)
5 " Fill-in
6 " Leading Bass function on/off
Specifying How the Bass Part Behaves
The function that sounds the lowest note of a fingered chord as the bass tone is called "Leading Bass. "
Off "
The bass part of the rhythm plays the root of the chord. For example, if you play the chord E-G-C (C major), the note
C is sounded as the bass.
On "
The bass part plays the lowest note of the chord you play. If you play the chord E-G-C (C major), the note E is
sounded as the bass.
The Leading Bass feature is always on while Split is off.

Chord Recognition When Split Is On

Sets how the unit recognizes rhythm chords while Split function (p. 2) is on.
Intelligent "
Plays chords even when basic chord tones are missing, allowing you to generate chords with very simple keyboard
playing. For details on how to play chords, refer to "Chord Fingering List" at the end of this manual.
Standard "
Normal chord recognition.
Preventing Doubled Notes When Connected to a Sequencer
(Local Control)
If a software synthesizer is connected to USB MIDI, turn this item "OFF. "
Since most software synthesizer have their Thru function turned on,
notes you play on the keyboard may be sounded in duplicate, or get
dropped. To prevent this, you can enable the "Local Off" setting so that
the keyboard and internal sound generator will be disconnected.
Copying a Song
(Copy Song)
A song that you recorded on this unit can be copied to a USB flash drive.
The copy-source song number is displayed; use the [-] [+] buttons to select the desired number, and press the [s] button to confirm
it.
The copy-destination song number is displayed; use the [-] [+] buttons to select the desired number, and press the [s] button to
confirm it.
Connecting to a Wireless LAN
This lets you establish a WPS connection.
The display indicates " Svr "; press the [y] (cancel) button or the [s] (execute) button to cancel or connect.
Connecting to a Wireless LAN
This lets you establish an ad-hoc connection.
The display indicates " Svr "; press the [y] (cancel) button or the [s] (execute) button to cancel or connect.

Viewing the Ad-Hoc Key

Of the five-digit ad-hoc key, the lower three digits are shown (the upper two digits are 00).
Various Settings (Function Mode)
(Stretch Tuning)
(Leading Bass)
Local Control
Sound Generator
(WPS Connection)
(Ad-Hoc Connection)
Software
USB MIDI
Synthesizer
In
USB MIDI
Out
Computer
15
page.
15
page.
15
page.
13