Initial Operation - Scheppach HL1300 Traduction Des Instructions D'origine

9.5 Mount trunk lifter (fig. 6)
Fasten the trunk lifter (5) with a hexagon screw (M10
x 55) and a self-locking nut between both of the
brackets, which are located on the right, lower end
of the splitter.
Next, align the holder arm (6) on the trunk lifter. A gap
of approx. 0.5 - 1 mm must be present between the
holder arm and trunk lifter.
Next, cut in the chain (4) on the splitting blade. (fig. 7)
9.6 Putting the splitter into the work position
Connect the splitter to the mains power. Be aware of
the motor's direction of rotation.
Lower both controller handles until the cylinder is
present above the drilled holes (d) is located in the
upper position. Insert both shafts into the drilled holes
and secure them with spring pins.
Then bring the splitting blade to the top position and
remove the support. You must store the support safe-
ly because it is needed every time the splitter is trans-
ported.
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!

10. Initial operation

Make sure the machine is completely and expertly
assembled. Check before every use:
• the connection cables for any defective spots
(cracks, cuts etc.).
• the machine for any possible damage.
• the firm seat of all bolts.
• the hydraulic system for leakage.
• the oil level.
• the safety devices
Checking the oil level (fig. 9)
The hydraulic unit is a closed system with oil tank,
oil pump and control valve. Check the oil level regu-
larly before every use. Too low an oil level can dam-
age the oil pump. The level of oil must be checked
when the riving knife is pulled back. If the oil level is
at the lower notch, then the oil level is at a minimum.
Should this be the case, oil must be immediately
added. The upper notch indicates the maximum oil
level. The machine must be on level ground. Screw
in the oil dipstick fully, to measure the oil level.
E- Motor
Check the running direction of the motor. If the split-
ting arm is not in the top position, bring the splitting
blade in the top position, using the return bracket or
handles. If the splitting arm is already in the top posi-
tion, activate the splitting mechanism by moving both
levers down. This will move the splitting arm down.
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
If the splitting blade does not move despite activation
of the handles or return bracket, immediately turn off
the machine. Turn the pole reversing unit in the plug-
in module (fig. 11) to change the rotational direction
of the motor.
Never let the motor run in the wrong direction!
This will inevitably destroy the pump system and
no warranty claim can be made.
Functional test
Test the function before every use.
Action: Result:
Push both handles Splitting knife goes down
towards below. to approx. 20 cm above
the table.
Let one handle loose, Splitting knife stops in the
then the other. desired position.
Push both handles Splitting knife returns to
towards up upper position
Warning!
Loosen the filling screw (d) before commission-
ing. Never forget to loosen the filling screw! Oth-
erwise, the air in the system will constantly be
compressed and decompressed with the result
that the seals of the hydraulic circuit will be de-
stroyed and the wood splitter can no longer be
used. In this case, the seller and the manufactur-
er will not be liable to warranty services.
Switching on and off (10)
Press the green button for switching on.
Press the red button for switching off.
Note: Check the function of the ON/OFF unit before
every use by switching on and off once.
Restarting safety in case of current interruption
(no-volt release).
In case of current failure, inadvertent pulling of the
plug, or a defective fuse, the machine is switched off
automatically. For switching on again, press anew
the green button of the switch unit.
Fix the splitter
Fix the splitter on the floor by fastening the two brack-
ets (f) to the support plate with two hexagon screws
(g) each. Then insert the tent peg (h) through the ex-
isting hole at an angle.
Splitting
• If the outside temperature is below 5°C, let the ma-
chine run idle for about 5 minutes so the hydraulic
system reaches its operating temperature. Place
the log under the splitting blade vertically. Caution:
The splitting blade is very sharp. Risk of injury!