Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Variable speed control knob
4. Forward/reverse switch
5. Drilling mode selector
6. Chuck
7. Depth stop
8. Side handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (ig. A)
u
Turn the grip counterclockwise until you can slide the side
handle (8) onto the front of the tool.
u
Rotate the side handle into the desired position.
u
Insert the depth stop (7) into the mounting hole as shown.
u
Set the drilling depth as described below.
u
Tighten the side handle by turning the grip clockwise.
(Original instructions)
Setting the drilling depth (ig. A)
u
Slacken the side handle (8) by turning the grip counter-
clockwise.
u
Set the depth stop (7) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
u
Tighten the side handle by turning the grip clockwise.
Fitting an accessory (ig. B)
u
Open the chuck by turning the sleeve (9) counterclock-
wise.
u
Insert the bit shaft (10) into the chuck.
u
Tighten the chuck by turning the sleeve clockwise.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, loors or ceilings, check for
the location of wiring and pipes.
Selecting the drilling mode
u
For hammer drilling in masonry and concrete, set the
operating mode selector (5) to the
u
For drilling in steel, wood and plastics, set the operating
mode selector (5) to the
Selecting the direction of rotation
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u
To select forward rotation, push the forward/reverse slider
(4) to the left.
u
To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
u
To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
If the tool has a variable speed control knob (3), set it
to the required speed range. As a general rule, use low
speeds for large diameter drill bits and high speeds for
smaller diameter drill bits.
u
For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed or at any speed preset with the variable
speed control knob (3). This option does not work in
reverse rotation.
u
To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
ENGLISH
s
r
position
position.
5

Publicité

Table des Matières
loading

Table des Matières