Description Of Symbols - Silverline 972660 Mode D'emploi

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important information
about the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction Manual
Caution!
DO NOT use in rain or damp environments!
For indoors use only!
T-130˚
Be aware of kickback!
Class I construction (double insulated for additional protection)
Dust extraction required or recommended
Always disconnect from the power supply when adjusting, changing
accessories, cleaning, carrying out maintenance and when not in use!
Important safety devices! Ensure correct function, maintain in
accordance with instructions and DO NOT disable!
Environmental Protection
Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
Conforms to relevant legislation and safety standards.
Technical Abbreviations Key
V
A, mA
n0
°
Ø
Hz
W, kW
/min or min
-1
dB(A)
m/s2
6
Volts
Ampere, milli-Amp
No load speed
Degrees
Diameter
Hertz
Watt, kilowatt
Operations per minute
Decibel sound level (A weighted)
Metres per second squared (vibration magnitude)
Original Instructions
Specification
Voltage: ................................................................................ 230-240V~, 50Hz
Power: ..................................................................................................... 350W
Duty Cycle: ...................................................... S2 30 minutes (short time duty)
No load speed - Sanding disc (n ): ....................................................1450min
0
Sanding disc size: ..............................................................................Ø150mm
Belt size: ..........................................................914 x 100mm & 915 x 100mm
Belt table tilt angle: ..............................................................................0° - 90°
Belt surface area: ....................................................................... 390 x 100mm
Table size: .................................................................................. 390 x 125mm
Belt speed: ..................................................................... 282 m/min <4.7m/s>
Belt Sander Dust Port: .............................Ø40mm (external), Ø37mm (internal)
Sanding Disc Dust Port:...........................Ø40mm (external), Ø34mm (internal)
Table tilt: ................................................................................................. 0-45°
Protection class: ..........................................................................................
Ingress protection: .....................................................................................IP20
Power cord length: ...................................................................................... 2m
Dimensions (L x W x H):.....................................................500 x 265 x 305mm
Weight: ...................................................................................................15.5kg
As part of our ongoing product development, specifications of Silverline products
may alter without notice.
Sound and vibration information:
Sound Pressure L :.............................................................................. 77dB(A)
PA
Sound Power L : ................................................................................ 90dB(A)
WA
Uncertainty K: ............................................................................................ 3dB
Vibration: ...........................................................................................<2.5 m/s
The sound intensity level for the operator may exceed 85dB(A) and sound protection
measures are necessary.
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and
limit the time of exposure if necessary. If sound levels are uncomfortable, even with ear
protection, stop using the tool immediately and check the ear protection is correctly fitted
and provides the correct level of sound attenuation for the level of sound produced by
your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long term exposure can lead to a chronic condition. If
necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do
not operate the tool with hands below a normal comfortable temperature, as vibration will
have a greater effect. Use the figures provided in the specification relating to vibration to
calculate the duration and frequency of operating the tool.
Sound and vibration levels in the specification are determined according to EN60745 or
similar international standards. The figures represent normal use for the tool in normal
working conditions. A poorly maintained, incorrectly assembled, or misused tool, may
produce increased levels of noise and vibration. www.osha.europa.eu provides information
on sound and vibration levels in the workplace that may be useful to domestic users who
use tools for long periods of time.
-1
2