Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 972660 Mode D'emploi

GB
h. Whenever possible, use a vacuum dust extraction system to control dust and
waste
i. Be especially careful when using a machine for both wood and metal sanding.
Sparks from metal can easily ignite wood dust. ALWAYS clean your machine
thoroughly to reduce the risk of fire
j. Empty the dust bag or container (where applicable) frequently during use,
before taking breaks and after completion of sanding. Dust may be an explosion
hazard. DO NOT throw sanding dust into an open fire. Spontaneous combustion may
occur when oil or water particles come into contact with dust particles. Dispose of
waste materials carefully and in accordance with local laws and regulations.
k. Work surfaces and sandpaper can become very hot during use. If there is
evidence of burning (smoke or ash), from the work surface, stop and allow the
material to cool. DO NOT touch work surface or sandpaper until they have had time
to cool
l. DO NOT touch the moving sandpaper
m. ALWAYS switch off before you put the sander down
n. DO NOT use for wet sanding. Liquids entering the motor housing can cause severe
electric shocks
o. ALWAYS unplug the sander from the mains power supply before changing or
replacing sandpaper
p. Even when this tool is used as prescribed it is not possible to eliminate all
residual risk factors. If you are in any doubt as to safe use of this tool, do not use it

Product Familiarisation

1. Tool Rest
2. Belt Sander Angle Nut
3. Motor Belt Housing
4. Disc Enclosure
5. Mitre Guide
6. Table
7. Mitre Guide Channel
8. Table Angle Indicator
9. Table Angle Gauge
10. Table Angle Knob
11. Disc Sander Dust Extraction Assembly
12. Disc Dust Port
13. Table Rod
14. Table Mounting Bolt
15. On/Off Switch
16. Rubber Feet
17. Belt Table Mounting
18. Belt Table Mounting Bolt Thread
19. Belt Roller Cover Screws
20. Belt Roller Cover
21. Tool Rest Mounting
22. Sanding Disc
23. Mitre Guide Angle Knob
24. Mitre Angle Indicator
25. Sanding Belt
26. Direction Indicator
8
27. Sanding Belt Height Adjustment Nut
28. Belt Release Lever
29. Belt Tension Knob
30. Belt Tension Spring Mechanism
31. Motor
32. Motor Belt Spindle (under cover)
33. Disc Table Mounting
34. Table Block
35. Table Bolt
36. Tool Rest Spring Washer
37. Tool Rest Bolt
38. Tool Rest Washer
39. Disc Sander Dust Extraction Assembly Screws (x 4)
40. Disc Sander Dust Extraction Assembly Washers (x 4)
41. Disc Enclosure Fittings (x3)
42. Disc Enclosure Mounting Grub Screw
43. Hex Key
44. Sanding Disc Base
45. Hook & Loop Adhesive Pad

Intended Use

• Bench-mounted combined belt and disc sander. Suitable for sanding a wide range of
materials including metal, wood and plastic. Sanding applications depend on fitted
belt or disc type and grit level. Not suitable for sanding materials that may produce
toxic particles or that may be highly flammable or have other dangerous material
properties. Not suitable for sanding with liquids including water and oil. Not intended
for commercial or industrial use.

Unpacking Your Tool

• Carefully unpack and inspect your new tool. Familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before attaching
or changing any accessories, or making any adjustments.
Note: It is highly recommended it is only connected to a circuit protected by a RCD or used
with a plug-in RCD.
Note: This tool is earthed and must only be connected to mains with a earth connection. Do
not attempt to use it without an earth connection.
Bench Mounting
Note: It is recommended the tool is securely mounted to a strong, stable workbench
(fittings not supplied) once assembled.
• There are 2 suitable holes in the base of the tool. Ensure all bolts are a good match for
the bench-fitting holes of the tool.
Assembling
• Fit the 4 supplied Rubber Feet (15) to the base of the tool