STAMOS S-MULTI 195 IGBT Manuel D'utilisation page 9

TIG TORCH:
1
1.
2
2.
3
3.
4
4.
5
5.
6
6.
MIG TORCH:
3
1
1. Nozzle
2
2. Collet
3. MIG welding torch
5. CONNECTING LEADS
INSTRUCTIONS FOR CONNECTING LEADS:
MMA WELDING MODE:
1. Set the switch (10) to MMA welding mode.
2. Connect the return lead to the socket marked with „+" (6), and tighten the locking nut.
3. Then connect the welding lead to the correct socket, marked with the number 11 on the diagram
and tighten the locking nut. ATTENTION! Polarization of the leads has to be different! All polarisation
information should be shown on the packaging supplied by the electrode manufacturer.
4. Now you can connect the power lead and turn the power on, once the return lead is connected to the
welded element, you can start working.
TIG WELDING MODE:
1. Set the switch (10) to TIG welding mode.
2. Connect the return lead to the socket marked with „+" (6), and tighten the locking nut.
3. Then connect the TIG welding lead to the socket marked with the „-" (11) sign and TIG welding control
lead to connector no. 8 and tighten the locking nut. Connect the gas lead directly to the gas canister.
Gas flow is adjusted using the knob on the welding torch.
4. Now you can connect the power lead and turn the power on, once the return lead is connected to the
welded element, you can start working.
MIG WELDING MODE / SYNERGIC SET:
1. Set the switch (10) to MIG welding mode.
2. MIG WELDING:
a. Connect the return lead to the socket marked with „-" (11), and tighten the locking nut.
b. Connect the polarisation change lead (12) to the socket marked with „+" (6)
c. Connect the MIG welding lead to the socket marked with the number 7.
d. Insert the correct filler wire and connect the gas canister to the connector at the back of the
machine.
EN
Back cap, long
Back cap, short
Collet
Torch handle
Collet inside housing
Ceramic nozzle
16
Rev. 20.03.2017
1. FLUX WELDING:
a. Connect the return lead to the socket marked with „+" (6), and tighten the locking nut.
b. Connect the polarisation change lead (12) to the socket marked with „-" (11)
c. Connect the MIG welding lead to the socket marked with the number 7.
d. Insert the correct FLUX filler wire
2. Now you can connect the power lead and turn the power on, once the return lead is connected to the
welded element, you can start working.
6. DISPOSING OF PACKAGING
The various items used for packaging (cardboard, plastic straps, polyurethane foam) should be kept, so that
the device can be sent back to the service centre in the best possible condition in case of any problems!
7. TRANSPORTATION AND STORAGE
Shaking, crashing and turning upside down of the device should be prevented when it is transported. Store
it in a properly ventilated surrounding with dry air and without any corrosive gas.
8. CLEANING AND MAINTENANCE
• Always unplug the device before cleaning it and when the device is not in use.
• Use cleaner without corrosive substances to clean surface.
• Dry all parts well before the device is used again.
• Store the unit in a dry, cool place, free from moisture and direct exposure to sunlight.
9. CHECK REGULARLY THE DEVICE
Check regularly that the device doesn ́ t present any damage. If there is any damage, please stop using the
device. Please contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. The more detailed your information, the better the
customer service will be able to answer your problem rapidly and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to
a loss of warranty!
Rev. 20.03.2017
EN
17