Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Auto atic
ode fro
synoptic panel re ote control
ress the
E
button twice to switch from manual to
automatic mode and adjust the temperature desired for the
room (on the panel or the
and
to set the temperature between
regulate the operating power required to reach it.
f the set temperature is lower than the room temperature,
the stove wor s at ower .
Shutdown
For greater co fort the stove and the air vents go off
at the sa e power at which it was operating.
ith the stove in operation mode press the
seconds (on the synoptic panel or remote control). he
shutdown procedure will begin and the countdown is
displayed. his varies according to the power at which it
is running when the shutdown phase begins.
he shutdown phase (which will e tinguish the ame
without leaving any unburnt material in the combustion
chamber and cool the stove), consists of:
ellet loading ceases.
entilation is activated at the level at which the stove
was operating.
Smo e e pulsion motor enabled.
Never unplug the stove during the shutdown process.
Setting the cloc
ress the
E
button for seconds and use the
eys to follow the instructions given on the display to
access the
loc
menu. his allows you to set the time on the
electronic control board.
hen press
E
and the following data appears in
sequence this can be adjusted:
day, month, year, hour, minutes, day of the wee .
hen Save appears on the display you can chec that
the settings have been entered correctly before con rming.
ress
E
to save the information ( Save
appears on the display).
ee ly ti er
ress the
E
button on the remote control for
seconds to access the time setting function and press the
ey to access the wee ly timer function
FF will appear on the display.
ma imum of three timer programs can be set for each
day of the wee .
s you con rm via the
E
options will appear:
-
o rog. (no program is set).
-
aily program (a single program is set for every day)
-
ee ly program (a program is set for each day of the
wee ).
ove from one to the other using the
se the
E
button to con rm the
option and access the selection of the number of programs
(ignition shutdown) to be set per day. se the
option to set the identical program s for every day
of the wee .
INSTRUCTIONS FOR USE
eys on the remote control
and 9 ...., and the stove will
ey for
and
then
rogram
button, one of the following
and
eys.
aily program
aily program
he following will be displayed if the
- o rograms.
- st daily program (one ignition and one shutdown per
day), nd daily program (same as before), rd daily program
(same as before).
se the
E
button to show them in reverse order.
f the st program is selected, the ignition time is shown.
he display shows:
gnition our
eys to change the hour and press
he display shows:
gnition
eys to change the minutes and press
n the same way, adjust the shutdown times. he program is
con rmed by pressing the
pears on the display.
hen con rming the
the day to which the program is to apply must be selected:
on;
ues;
ed;
nce you have chosen the day by scrolling through them
with the
and
eys, con rm by pressing
proceed with the settings of the programs in the same way
as for the
aily program , selecting whether or not to
enable a program for each day of the wee and choosing
the number and times of interventions.
Should you ma e a mista e whilst setting the programs
you can e it without saving by pressing the
Note on a e variability
he ame may vary depending on the type of pellets
used, in addition to normal variability of the solid fuel
ame and regular cleaning of the combustion chamber
carried out automatically by the stove.
N.B. he automatic cleaning process performed by the
stove does not replace the need for the user to vacuum the
stove when cold, prior to ignition).
Pellet reserve warning
Stoves are equipped with an electronic pellet detection
system. he detection system is integrated into the electronic
control board, allowing the stove to monitor how many ilos
of pellets are left. his veri cation is implemented at any point
whilst the stove is in operation mode. For correct system ope-
ration, it is important that the following procedure is adhered
with during the rst ignition (that must be implemented by the
E LER). efore starting to use the pellet detection system,
you must load and consume a full sac of pellets. his allows
for a brief running-in of the loading system. ence, load
of pellets. hen press the reserve button once, thereby storing
the data into the memory that
From now on the display will show the remaining pellets
as they decrease in g ( ... ... ).
Each time pellets are reloaded you must enter the quantity.
E.g. when loading
g, simply press the pellet load button
to enter this into the memory. For other quantities, or in the
event of an error, you can specify the quantity using the pellet
reserve menu as follows:
ress the
E
button for seconds to view the SE
ress
or consecutively to view RESER E.
ressing the
ey increases the g to be loaded, pressing the -
ey reduces the g, pressing the - ey repeatedly sets the load
to
g (R on the display), which ma es it possible to cancel
the residual load.
- 39
-
ey is pressed:
. ; use the
E
to con rm.
inutes
. ; use the
E
to con rm.
E
button when Save
ee ly program
hurs; Fri; Sat; 7 Sun
E
and
ey.
g have been loaded.
ap-
g
S.
Publicité
Table des Matières
