Section
4 . How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . .15-16
6 . Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
READ AND SAVE THESE INSTRUCTIONS
WARNING
!
1. Read your owner's manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring, and do not operate fan without blades.
2. All wiring must be in accordance with the National
Electrical Code "ANSI/NFPA 70-2017" and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as "Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less", and use
the mounting screws provided with the outlet box.
Table of Contents
Page
ection
S
10 . Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11 . Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
14 . Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-33
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . 35
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
French . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Safety Instructions
4. Follow the recommended instructions for the proper
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
NOTE:
controls.
NOTE:
where necessary before installation.
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To reduce the risk of fire or electrical shock, this fan
should only be used with fan speed control, Model No.
UC7067RAI, manufactured by Rhine Electric Co., Ltd.
To avoid fire, shock or injury, do not use a Luminance
Brands or any other brand of control not specifically
approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury or
property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
2
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
CAUTION
!
This fan is suitable for use with solid-state speed
All set screws must be checked and re-tightened
WARNING
!
Page
U.L. Model No.: CF605