Step 1 Remove Packaging; Step 2 Install Water Line - Monogram ZIR300NPKII Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Installation Instructions - Dual Retro-Fit Installation

STEP 1 REMOVE PACKAGING

WARNING
appliance is top heavy. Use extreme caution with
moving to prevent tipping over which could result in
death or serious injury.
Remove outer carton and external packing from units.
Inspect for damage.
Ensure the flooring that the units are set is clean/
free of debris that could be collected on to, or
pinched in front of the wheels and damaging the
floor. Additionally, it is recommended that the floor
be protected with a plastic covering through out the
installation process.
Remove hardware kit from top drawer.
If installation requires a
limiter pin must be installed
in the top hinge
BEFORE
the unit is removed from
the skid. Pin is located in
the hardware kit.
- Open the door
approximately
45°,
wider than
90°,
to expose
the hole in the back hinge
bracket and install the
limiting pin. Pin must be
fully seated in the bracket
or the door will not close properly.
Remove front access cover from unit by removing 2
T20 Torx screws. Place the cover and screws to the
side for future
installation.
3/8" Drive
Screws
Shipping
Bracket
7/16" Drive
Screws
Remove three 3/8" drive screws and two 7/16" drive
screws from each side of the unit to release it from
the skid. Tip the unit from the side enough to remove
the shipping material from under the unit, but above
the skid (both sides)
CAREFULLY roll the unit off the back side of the skid.
Handle from side only with a hand truck.
31-49133-1
Tip Over Hazard.
90°
door opening, the hinge
but no
T20 Torx Screws

STEP 2 INSTALL WATER LINE

WARNING
This
A cold water supply is required for automatic icemaker
and AutoFill pitcher operation. The water pressure
must be between 40 and 120 p.s.i. (275-827 kPa).
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the
line of water.
Install a shut-off valve between the water valve and
cold water pipe in a basement or cabinet. The shut-
off valve should be located where it will be easily
accessible.
Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in
many water supply kits. Before purchasing, make sure
a saddle type valve complies with your local plumbing
codes.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle
Top
valves are illegal and use is not permitted in
hinge
Massachusetts. Consult with your licensed plumber.
Connect the jumper water line from the ZTKC42 or
ZTKC48 Trim Retro Kit to the house cold water line.
Tighten the compression nut hand tight, then tighten
one additional turn with a wrench. Overtightening
can cause leaks!
Connect the other end of the jumper water line to the
water fitting tee supplied in the trim retro kit. Tighten
the compression nut hand tight, then tighten one
additional turn with a wrench. Overtightening can
cause leaks!
Route 1/4" OD copper or SmartConnect
(WX08X10006) plastic tubing between water fitting
tee and the water connection location at the front of
the unit.
SmartConnect
available. One 8' (2.4m) water line (WX08X10006) is
needed for each unit.
Tubing should be long enough to extend to the front
of the unit. Allow enough tubing to accommodate
bend leading into the water line connection. Unit
must be tipped on its side to route waterline
underneath and to the front of the appliance.
21
Connect to potable water supply
only.
Refrigerator Tubing Kits are
Water Line Jumper
Water Fitting Tee

Publicité

Chapitres

Table des Matières
loading

Table des Matières