Maintenance; General; Daily Cleaning; Replacing Display Light Bulbs - Hatco GLO-RAY GRSDH Séries Manuel D'installation Et D'utilisation

General

Hatco Glo-Ray Merchandising Display Warmers are designed
®
for maximum durability and performance with minimum

maintenance.

WARNING
ELECTRIC SHOCK HAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Do not clean unit when it is energized or hot.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
414-671-6350 or International fax 414-671-3976.

Daily Cleaning

To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
IMPORTANT—DO NOT use paper towel or glass cleaner to
clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and wipe down the product dividers.
3. Wipe down all exterior and interior surfaces using a water-
dampened cloth. a non-abrasive cleaner may be used for
difficult stains. Hard to reach areas should be cleaned
using small brush and mild soap.
4. Clean the glass side panels using a standard glass
cleaner.
5. Clean the plastic sneeze guards and flip-up doors (if
equipped) using soft cleaning cloths, mild soap, and water,
if equipped. NOTICE: Do not use paper towel or glass
cleaner on plastic surfaces—scratching may occur.
Form No. GRSDCEM1-0514

Replacing Display Light Bulbs

Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display light is an incandescent bulb that illuminates the
warming area. The bulb has a special coating to guard against
injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF standards
for food holding and display areas. For 120 and
120/208–240
02.30.043.00. For 200, 220, 240, 220–230 and
230–240 V applications, use Hatco P/N 02.30.058.00.
NOTE: Shatter-resistant halogen bulbs are available in place
of the standard incandescent bulbs. Halogen bulbs
have a special coating to guard against injury and food
contamination in the event of breakage. For 120 and
120/208–240
02.30.081.00. For 220, 240, 220–230, and 230–240 V
applications, use Hatco P/N 02.30.082.00.
Use only Genuine Hatco Replacement Parts when service
is required. Failure to use Genuine Hatco Replacement
Parts will void all warranties and may subject operators of
the equipment to hazardous electrical voltage, resulting in
electrical shock or burn. Genuine Hatco Replacement Parts
are specified to operate safely in the environments in
which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that will
allow them to operate safely in Hatco equipment.
15
MAINTENANCE
WARNING
V applications, use Hatco
V applications, use Hatco
WARNING
P/N
P/N