Maintenance; General; Daily Cleaning; Ground Fault Circuit Interrupters - Hatco Glo-Ray GR3SDH Série Manuel D'installation Et D'utilisation

English

General

Hatco Heated Glass Merchandisers are designed for maximum
durability and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or

maintenance.

• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
Do not move or relocate unit for cleaning. Unit is bulky
and heavy.

Daily Cleaning

To maintain performance and preserve the finish of the Heated
Glass Merchandiser, clean the unit daily.
NOTICE
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Form No. GR3SDM-0920
1. Turn off the unit, unplug the power cord(s), and allow the
unit to cool.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
2. Remove and discard any remaining food product.
3. Wipe down the hardcoated heated base and all metal
surfaces using a clean, damp cloth. Stubborn stains may be
removed with a good non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild soap.
4. Clean the heated glass shelves and glass side panels using
ordinary glass cleaner and a soft cloth or paper towel.
5. If equipped, clean the plastic sneeze guards or flip-up
doors using soft cleaning cloths, mild soap, and water.
NOTICE: Do not use paper towel or glass cleaner on
plastic surfaces—scratching may occur.

Ground Fault Circuit Interrupters

Heated Glass Merchandisers are supplied with up to two,
built-in Ground Fault Circuit Interrupters (GFCI). GFCIs are
designed to turn off electrical power and help prevent damage
to the internal components when there is a short circuit or
electrical fault.
To reset a GFCI:
1. Make sure the unit is plugged in and all ON/OFF switches
are in the ON position.
2. Push the reset button.
NOTE: The unit must be plugged in and turned on for the GFCI
to reset. If the unit is off, the GFCI will not reset.
If a GFCI continues to trip, contact an Authorized Hatco Service
Agency.
RESET Button
Ground Fault Circuit Interrupters
11
MAINTENANCE
Ground Fault
Circuit Interrupter