Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 982593 Mode D'emploi

GB
• Wear suitable protective anti-vibration gloves that are non-fabric or
coated fabric to prevent loose strands of material catching in the rotating
drill bit. Discard gloves immediately if material is visibly frayed
• Drilling can produce large volumes of dust and debris that may be toxic.
Wear respiratory protection suitable for the work being undertaken. A
minimum rating of FFP2 is recommended
• SDS drills produce high volumes of noise and suitable ear protection
must be worn at all times while operating the tool
• SDS drills produce a very high level of vibration when operating in
hammer or chisel mode. Frequent breaks are advised
• Only use SDS Chisels or Points with SDS drills that can disengage rotary
drilling mode
• Use metal and voltage detectors to locate concealed electric, water or
gas lines. Avoid touching live components or conductors
• Extension cable reels used with this tool must be completely unwound.
Minimum conductor cross section: 1.25mm
• Extension reels used outside should be designed for outdoor use and
should feature water-protected sockets and correct cable insulation
• When using an SDS drill outdoors, an RCD device must be used either by
connecting to a socket which incorporates an RCD, or through use of
an inline RCD
• Ensure that the chisel or drill bit is securely fixed in the chuck before
operating the tool. Insecure drill bits can be ejected from the machine,
causing a hazard
• Ensure lighting is adequate
• Use both hands when operating this tool
• Always use the auxiliary handle supplied with the tool
• Do not place pressure on the tool - to do so could shorten its service life
• Drill bits become hot during operation. Allow to cool prior to handling
• If you are interrupted when operating the drill, complete the process and
switch off before diverting your attention elsewhere
• Always disconnect the SDS drill from the electric supply before changing
a chisel or drill bit
• Examine the chuck regularly for signs of wear or damage. Have damaged
parts repaired by a qualified service centre
• Always wait until the drill has come to a complete stop before placing
it down
• On completion of the work, disconnect the tool from the power source
and remove the chisel/bit from the machine
• Periodically check all nuts, bolts and other fixings and tighten where
necessary
• Visibly check the tool after use, especially the power cable, which can be
damaged by sharp masonry
• Always fit the dust guard to the bit in use to prevent damage from debris
entering the SDS chuck
• If operating the tool causes discomfort in any way, stop immediately and
review your method of use
6 6
2

Product Familiarisation

1 SDS Plus Chuck
2 Chuck Protective Cover
3 Rotation Selection Switch
4 Gearbox Cover
5 On/Off Trigger Switch
6 Hammer Selection Switch
7 Variable Speed Control
8 Motor Vents & Brush Access Cover
9 Auxiliary Handle
10 Motor Vents
11 Chuck Key
12 Pot of Grease
13 Chisel
14 Point
15 Dust Guard
16 8mm Masonry SDS Plus Drill Bit
17 10mm Masonry SDS Plus Drill Bit
18 12mm Masonry SDS Plus Drill Bit
19 Hex Key
20 13mm Keyed Chuck
Additional Supplied Accessories (not shown):
Blow moulded case

Intended Use

Portable medium-duty mains powered power drill optimally designed for
drilling masonry and breaking light masonry. It is also capable of drilling
wood and metal with the supplied standard chuck with SDS Plus connector.

Unpacking Your Tool

• Carefully unpack and inspect your new sander. Familiarise yourself with
all its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply
before attaching or changing any accessories, or making any adjustments.
IMPORTANT:
• Before first use and after every 6 hours (approx.) of use, fill the gearbox
cavity with gearbox grease. A Pot of Grease (12) is supplied for initial use.
See 'Gearbox Maintenance' for application guidance
• Always check there is sufficient grease in the gearbox cavity before
using the drill