Additional Safety Instructions For Pneumatic Power Tools; Product Familiarisation - Silverline 868625 Mode D'emploi

GB
Additional Safety Instructions for
Pneumatic Power Tools
Air under pressure can cause severe injury:
• Always shut off air supply, drain hose of air pressure and disconnect tool
from air supply when not in use, before changing accessories or when
making repairs
• Never direct air at yourself or anyone else
• Whipping hoses can cause severe injury. Always check for damaged or
loose hoses and fittings
• Whenever universal twist couplings (claw couplings) are used, lock
pins should be installed and whipcheck safety cables should be used
to safeguard against possible hose-to-tool or hose-to-hose connection
failure
• Do not exceed the maximum air pressure stated on the tool
• Never carry an air tool by the hose
Additional Safety for Drills
• Important: It is imperative to follow all national safety regulations
concerning installation, operation and maintenance
• Do not allow anyone under the age of 18 years to use this tool, and
ensure that operators are qualified and familiar with the operating and
safety instructions
• When using the drill, use safety equipment including safety glasses or
shield, ear defenders, and protective clothing including safety gloves.
Wear a dust mask if the drilling operation creates dust
• Use metal and voltage detectors to locate concealed electric, water or
gas lines. Avoid touching live components or conductors
• Ensure that the lighting is adequate
• Ensure that the drill bit is securely fixed in the chuck. Insecure drill bits
can be ejected from the machine causing a hazard
• Ensure that the drill bit is in NOT contact with the workpiece prior to
starting up the tool
• Before drilling, check that there is sufficient clearance for the drill bit
under the workpiece
• Use both hands when operating this tool
• Do not put excessive pressure on the tool, to do so would shorten its
service life
• Drill bits get hot during operation, allow to cool prior to handling them
• Never use your hands to remove sawdust, chips or waste close by the bit
• If you are interrupted when operating the drill, complete the process and
switch off before looking up
• Where possible, use clamps or a vice to hold your work
• Always disconnect the drill from the air supply before changing a bit
• Examine the chuck regularly for signs of wear or damage. Have damaged
parts repaired by a qualified Silverline service centre
• Always wait until the drill has come to a complete stop before putting
it down
• On completion of the work, disconnect the tool from the air source and
remove bit from the machine
• Periodically check all nuts, bolts and other fixings and tighten where
necessary
6

Product Familiarisation

1 Quick Connector
2 Trigger
3 Safety Catch
4 Keyless Chuck
5 Handle
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Intended Use
One speed drill, powered by compressed air from a compressor. Uses drill
bits and other compatible accessories with a shaft diameter up to 9.5mm
(3/8").
Note: This air drill does not feature a torque clutch and must therefore not
be used for screw driving or similar applications.
Before Use
Fitting the quick connector
Note: This tool is supplied with two different male airline quick connectors:
EQ-4 – commonly used in Europe
EN-6 – mainly used in the UK
EQ-4
Europe
• Please choose the connector that is compatible with the airline system
you are using, and install as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick
Connector (4). This will help to maintain an air tight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not
come off when the thread is screwed into the tool.
2. Remove the protective plug from the air inlet
3. Using a spanner (not included) screw the quick connector into the air
inlet located at the base of the handle
4. Connect to airline, pressurise carefully and carry out a leak check
(e.g. by spraying small amounts of soapy water on to the outside of
the connectors)
• Air lines fitted with matching female quick connectors will now be a push
fit to the tool
EN-6
UK