Installation Instruction - Faber Cassette L Pebble Mode D'emploi

Always ensure that the fi re is sitting on a level fl oor.
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and
dry the sump.
Once installed, never move this fi re or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air fi lters must be cleaned once every two weeks, particularly in
hard water areas.
The fi re appliance should never be operated if the lamps are not working.

Installation Instruction

The lamps should be regularly inspected as described under 'Maintenance' and 'Changing lamps'.
Ensure that all packing items are removed (read any warning labels carefully).
Retain all packing for possible future use, in the event of moving or returning the appliance to your supplier.
To reduce heat losses and to prevent any chimney updraught affecting the operation of your fi re we
recommend that the chimney fl ue is blocked off, ensure that there is a slight gap for ventilation.
To install the appliance;
Hold the fi re by the sides and gently manoeuvre into position. Plug the fi re into a 13amp/240 volt outlet. Ensure that
the supply cable exits at the front of the fi re, at the right or left hand corner to suit your supply socket location and is
not trapped under the fi re such that it might cause it to be damaged.
Before switching on the appliance, please read the following instructions.
Before using the manual controls fi rstly fi ll the water tank (See 'Maintenance', 'Filling the water tank').
Manual Controls.
The manual controls are located behind the drawer.
(See Fig.2 for Manual Control lay out)
Switch 'A':- Controls the electricity supply to the fi re.
Note: This switch must be in the 'ON' ( I ) position for the fi re to operate
Switch 'B':- Controls the function of the fi re.
Press once to turn on fl ame effect. This will be indicated by one beep.
Although the main lights operate immediately it will take a further 30 seconds before the fl ame effect starts.
Press to put fi re in to standby mode.
This will be indicated by one beep.
Control Knob 'C':- Controls the intensity of the fl ame effect.
Turning the control knob up increases the fl ame effect, turning the control knob down will decrease the fl ame
effect.
When the water tank is empty the main lamps go out. See instructions under 'Maintenance', 'Filling the water tank'.
When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the fl ames return.
Remote Control Operation
On the control panel, Switch A (see Fig.2) must be in the 'ON' ( I ) position in order for the remote control to operate.
There are 2 buttons on the remote control. (See Fig.7)
To operate correctly the remote must be pointed towards the front fuel effect.
The remote control functions are as follows:
Press once to turn on Flame effect only.
This will be indicated by one beep.
Standby
This will be indicated by one beep.
Battery Information.
1. Unclip the battery cover on the back of the remote control. (See Fig.7)
2. Install AAA batteries into the remote control.
3. Replace the battery cover.
Discard leaky batteries.
Dispose of batteries in the proper manner according to provincial and local regulations.
Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are
not replaced at the same time, if disposed of in a fi re, or if an attempt is made to charge a battery not intended to be
recharged.
Tips for using your appliance.
1. Only pull out the drawer when its time to refi ll the water tank or change a lamp, otherwise it may lead to excess water
in the sump and reduced fl ame effect. If this happens empty the water from the sump as instructed under 'Maintenance'.
2. With the fl ame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as long
than when it is at maximum fl ame setting.
3. Do not tilt or move the fi re while there is water in the tank or sump.
17