General Information; Installation Instructions; Before You Start - Faber CAS500 Manuel D'utilisation

General Information

Only use filtered water in this appliance.
Unpack the appliance carefully and retain the packaging for possible future use, in the event of moving or returning the
fire to your supplier.
Always ensure that the appliance is sitting on a level surface.
The appliance is a flame effect only.
The appliance is designed to be built into a surround or built into a wall.
Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is
related to the operation of the flame effect. This is normal and should not be a cause for concern.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air filters must be cleaned once every 2 weeks, particularly in hard water
areas.
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the
sump.
The sump and the water tank in this product are treated with a biocidal product, Silver Biocide. This conforms with the
latest relevant ISO standard
Do not drink the water from the sump or from the water tank(s)
This appliance is intended to be permanently connected to the water mains and not connected by a hose-set

Installation Instructions

This section describes how to set up your fire.

BEFORE YOU START

1. Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible
future use.
2. Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
3. Ensure that the appliance is sitting on a level surface
4. Lift off the metal top plate to gain access to the appliance. Keep the top plate with the packing for possible future
use. (Fig.2)
Installation Guide
This product can be built into a wall, surround or structure. Please take note of the product dimensions in (Fig.1) and
build your wall, surround or structure accordingly. You are required to leave a minimum of 400mm from the base of the
fuelbed to any shelf/enclosure above the product. This will allow enough space above the product to allow the flames to
form fully and not to be obstructed.
This product needs free ventilation from underneath to operate correctly. There are slots on the underside of the product
to allow this free air through the product (Fig.4) The free ventilation helps keep the electronic components cool, allow
the mist to evacuate the sump and lift out of the product effortlessly.
THE AREA OF FREE VENTILATION THE CAS500 REQUIRES IS A MINIMUM OF 210CM
THE AREA OF FREE VENTILATION THE CAS1000 REQUIRES IS A MINIMUM OF 420CM
SEE Fig 14 AND Fig 15 FOR EXAMPLES OF THE REQUIRED VENTILLATION
Surround Design
The CAS500 and CAS1000 are designed to be built into a surround/wall. Using the dimensions provided in (Fig1). you
can design a cavity for the appliance. Be sure to allow room under and around the appliance for the water connection
and the electrical connection. Once the surround/wall is prepared you can put the appliance in place. Fit the appliance
so you ensure that it is centered. When you have settled on a position, lift off the Fuelbed and using appropriate screws
for the surround/wall, screw through the formed holes in the left and right side panels securing the appliance in place.
Mains Water direct connection:
It is recommended that you consult a qualified plumber to ensure a safe and secure installation.
An Adapter is supplied to connect the ¼" PVC tube of the product to the ½" mains water pipe.
1. Position the water filter (supplied) in a suitable location. This may need to be accessed for future replacement.
2. Measure and cut the PVC tube (1m supplied) in order that the water can flow from the Adapter to the filter, and then
from the filter to the appliance.
3. Check filter is positioned in correct alignment – there is a "flow" direction marking on the filter.
4. It is recommended to have already installed a ball valve/tap to turn off the water flow.
5. With the water supply turned off, the Adapter can be used to connect the ½" water pipe to the ¼" PVC tube.
6. Connect PVC tube from the Adapter to the filter. (Fig 4)
7. Flush out the newly plumbed pipe before connecting to the appliance.
8. Connect PVC tube from the filter to the appliance.
9. Ensure that the appliance tap is open. (Fig 4)
18
.
2
.
2