Principle Of Operation; Safety Information - EdilKamin LOGO Installation, Usage Et Maintenance

PRINCIPLE OF OPERATION

The LOGO stove produces hot air using wood pellets as fuel,
with electronically controlled combustion. Hereunder is the
explanation of its functions (the letters refer to fi gure 1).
The fuel (pellets) is provided by the storage hopper (A) and,
to the combustion chamber (D) by means of a feed screw (B),
which is driven by a gear motor (C).
The pellets are ignited by the air that is heated by an electrical
resistance (E) and drawn into the combustion chamber
by a smoke extractor (F).
The fumes produced during the combustion process are ex-
tracted from the hearth by the same centrifugal fan (F) and
expelled through the outlet (G) located on the lower part at the
back of the stove.
The hearth is covered in cast iron, and closed frontally by a
glass ceramic door (to open use the dedicated "cold hand"
handle").
Fuel quantity, smoke extraction and combustion air supply
are all controlled by an electronic control board, which is
equipped with Leonardo ® software to achieve high combustion
effi ciency and low emissions.
The synoptic panel (M) is installed on the top, through which
all phases of operation can be displayed and controlled.
The main phases can be controlled via the optionally supplied
remote control.
The main functions can also be controlled by remote control.
Aserial port is found at the back of the stove (optional cable:
code 640560) to be connected to devices that allow remote
ignition (e.g. remote telephone, local thermostat).
D
F
fi g. 1

SAFETY INFORMATION

The LOGO stove is designed to heat, through automatic pellet
combustion in the hearth, the room where it is installed, both
by radiation and the air that comes out of the front grille.
• The only risks that may derive from using the stove pertain
to non-compliance with installation instructions, direct contact
with live electrical parts (internal), contact with the fi re or hot
parts (glass, pipes, hot air output), or foreign substances being
put in the stove.
• Only use wood pellets as fuel.
• Should components fail, the stoves are equipped with safety
devices that guarantee automatic shutdown. These are activated
without any intervention required.
• In order to function correctly, the stove must be installed in
accordance with the instructions given herein and the door
must not be opened during operation: combustion is fully
automatic and requires no intervention.
• Under no circumstances should any foreign substances be
entered into the hearth or hopper.
• Do not use fl ammable products to clean the smoke channel
(the fl ue section connecting the stove smoke outlet to the
chimney fl ue).
• The hearth and hopper parts must only be cleaned when
COLD.
• The glass can be cleaned when COLD with a suitable product
(e.g. GlassKamin Edilkamin) and a cloth.
• Do not clean when hot.
• Make sure the stove is installed and ignited the fi rst time
by Edilkamin-qualifi ed CAT personnel (technical assistan-
M
ce centre) in accordance with the instructions provided here
within; this is an essential requirement for the validation of the
guarantee.
• When the stove is in operation, the exhaust pipes and door
become very hot (do not touch without wearing the thermal
glove).
A
• Do not place anything, which is not heat resistant near the
stove.
• NEVER use liquid fuel to ignite the stove or rekindle the
embers.
B
• Do not obstruct the ventilation apertures in the room where
the stove is installed, nor the air inlets of the stove itself.
E
• Do not wet the stove and do not go near electrical parts
with wet hands.
C
• Do not use reducers on the smoke exhaust pipes.
G • The stove must be installed in a room that is suitable for
fi re prevention and equipped with all that is required (power
and air supply and outlets) for the stove to function correctly
and safely.
• Should ignition fail, DO NOT re-ignite until you have
emptied the combustion chamber.
•ATTENTION: THE PELLET EMPTIED FROM THE
COMBUSTION CHAMBER MUST NOT BE DEPOSI-
TED INSIDE THE HOPPER.
- 21
-