About Global Settings; Other Functions; Restoring The Factory Settings - Korg KingKORG Manuel D'utilisation

KingKORG Owner's manual

About global settings

Switch to Global mode when you want to change settings that apply to
the entire KingKORG or when you want to make MIDI‐related settings.
Global mode contains various settings such as master tune,
transpose, and global MIDI channel. (PG: "5. GLOBAL parameters")
Changes you make to these settings will be lost if you turn off
the power without saving. Be sure to save your settings if you
want to keep them. (OM: p.21 "1. Saving global settings")

Other functions

1.
Initializing a program
Here's how to initialize the settings of the selected program.
This procedure will initialize the settings of the that's being
edited program. It will not change the contents stored in
internal memory.
If you want to save the initialized state, save the program.
(OM: p.21 "2. Saving a program")
1.
Select the program that you want to initialize. (OM: p.13
"Selecting a program")
2.
Use the PAGE +/- buttons to access the PROGRAM "u01:
Utility" page, and press the value dial.
A screen will ask you to confirm that you want to initialize the
program.
TIP: If you decide not to initialize, press the SHIFT/EXIT button.
3.
Press the value dial once again.
When initialization is finished, the display will indicate
"Complete!" and you will automatically return to the top screen.
2.
Copying a timbre
Here's how you can copy the settings of another program's timbre to
a timbre (either A or B) of the currently selected program.
This operation recalls settings to a timbre of the program that's
being edited . It will not change the contents stored in internal
memory.
Only one timbre can be copied at a time.
1.
First select the program that includes the copy-destination
timbre. (OM: p.13 "Selecting a program")
2.
Use the PAGE +/- buttons to access the PROGRAM "u02:
Utility" page, and press the value dial.
3.
Turn the value dial to select the program that contains the
copy-source timbre, and press the dial to confirm your selection.
When selecting a program, the TIMBRE A or B select button will
light depending on the timbres used by the copy‐source
program.
20
The TIMBRE A or B select buttons will not respond if you
press them at this time.
4.
Confirm the copy-source timbre.
If the copy‐source program uses two timbres, the copy‐source
timbre button will blink. Select the desired timbre if necessary,
and press the value dial to confirm your selection.
TIP: While the TIMBRE A or B select button is blinking, you can
also make your choice by pressing a button.
5.
Confirm the copy-destination timbre.
If the copy‐destination program uses two timbres, the TIMBRE
A or B select button will blink. As necessary, turn the value dial
to select the copy‐destination timbre, and press the value dial to
confirm your selection.
6.
A confirmation screen will appear in the main display; verify
the settings, and press the value dial.
When the copy is completed, the display will indicate
"Complete!" and you will return to the top screen of the "u02:
Utility" page.
TIP: If you want to save the copied state, save the program. (OM:
p.21 "2. Saving a program")
TIP: You can press the SHIFT/EXIT button to return to the previous
step. If you decide not to copy a timbre, press the SHIFT/EXIT
button several times.
3.

Restoring the factory settings

Here's how to restore the KingKORG's programs and global data
settings to their factory‐set condition. The factory settings are called
the "preload data." To return to the factory‐set state, execute the
Load Preload operation.
When you execute Load Preload, the factory set data will
overwrite the data you've saved in internal memory. Make
sure that you don't mind losing this data.
Do not touch the KingKORG's knobs or keyboard while the
Preload operation is in progress. Never turn off the power
during this process.
Of factory‐set programs 1–300, programs 201–300 (programs
containing no preset data) will not return to their factory‐set
state. If programs are saved in these locations, they will remain
in that state.
You can't execute the Load Preload operation if memory
protect is turned on. Turn off memory protect before you