Specifications - Sony VPL-X2000U Manuel D'installation

Specifications

Optical characteristics
Projection system 3 LCD panels, 1 lens, 3-primary
color optical shutter system
LCD panel 1.8-inch XGA LCD panel,
2,359,296 pixels
(786,432 pixels × 3)
Lens Option
Light output ANSI lumen
120 W UHP × 4
Lamp
Electrical characteristics
Color system NTSC
PAL-M system, switched
automatically
Resolution 600 horizontal TV lines (video
input)
1024 × 768 dots (RGB input)
Acceptable computer signal
fH: 15 to 94 kHz
fV: 40 to 120 Hz
Max. 5 W + 5 W, 90 × 50 mm
Speakers
5
(3 /
Input/Output
CONTROL S IN/PLUG IN POWER: Stereo
minijack, 5 Vp-p, plug in power,
DC 5 V, maximum output 60 mA
OUT: Stereo minijack, 5 Vp-p
REMOTE RS-232C/422A
D-sub 9-pin (female)
(For details, see "Pin assignment"
on page 70 (GB).)
PJ COM IN: D-sub 9-pin (male)
OUT: D-sub 9-pin (female)
(For details, see "Pin assignment"
on page 70 (GB).)
TRIG Minijack
Power on: DC 12 V, output
impedance: 4.7 kilohms
Power off: 0 V
..........................................................................................................................................................................................................
1) ANSI lumen is a measuring method of American
National Standard IT 7.228.
68
(GB)
1) 2,400 lm
/PAL/SECAM/NTSC
3.58 4.43
× 2 inches), stereo
8
S VIDEO (priority to Y IN/C IN) (only for VPL-
X2000U/X2000M)
/
VIDEO (only for VPL-X2000U/X2000M)
AUDIO IN (only for VPL-X2000U/X2000M)
INPUT A
IN: Mini DIN 4-pin type (male)
Y (luminance): 1 Vp-p ± 2 dB
sync negative, 75 ohms
terminated
C (chrominance): Burst 0.286
Vp-p ± 2 dB (NTSC), 75 ohms
terminated
Burst 0.3 Vp-p ± 2 dB (PAL), 75
ohms terminated
OUT: Loop-through mini DIN 4-
pin type (male)
Loop-through output from the S
VIDEO IN connector
Y IN: BNC type
1 Vp-p ± 2 dB sync negative, 75
ohms terminated
C IN: BNC type
Burst 0.286 Vp-p ± 2 dB
(NTSC), 75 ohms terminated
Burst 0.3 Vp-p ± 2 dB (PAL), 75
ohms terminated
IN: BNC type
Composite video, 1 Vp-p ± 2 dB
sync negative, 75 ohms
terminated
OUT: Loop-through BNC type
Loop-through output from the
VIDEO IN connector
Phono type (stereo)
500 mVrms, impedance more
than 47 kilohms
Analog RGB/component: BNC
type
R/R-Y: 0.7 Vp-p ± 2 dB positive,
75 ohms terminated
G: 0.7 Vp-p ± 2 dB positive, 75
ohms terminated
G with sync/Y: 1 Vp-p ± 2 dB sync
negative, 75 ohms
terminated
B/B-Y: 0.7 Vp-p ± 2 dB positive,
75 ohms terminated
SYNC/HD: Composite sync: 0.6–8
Vp-p, high impedance, sync
positive/negative
Horizontal sync: 0.6–8 Vp-p,
high impedance, sync positive/
negative