Hitachi DS 9DVF3 Mode D'emploi page 15

4. The scope and suggestions for uses
The usable scope for various types of work based on the
mechanical structure of this unit is shown in Table 6.
Work
Wood
Drilling
Steel
Machine screw
Driving
Wood screw
5. How to select tightening torque and rotational speed
Use
Machine screw
Driving
Wood screw
Wood
Drilling
Metal
CAUTION
○ The selection examples shown in Table 7 should be
considered as general standard. As diff erent types of
tightening screws and diff erent materials to be tightened
are used in actual works proper adjustments are naturally
necessary.
○ When using the driver drill with a machine screw at HIGH
(high speed), a screw may damage or a bit may loose
due to the tightning torque is too strong. Use the driver
drill at LOW (low speed) when using a machine screw.
6. Mounting and dismounting of the bit
<For double sleeve chuck>
(1) After inserting a driver bit, etc. into the keyless drill chuck,
fi rmly grasp the ring and tighten the sleeve by turning it
toward the right (in the clockwise direction as viewed
from the front) (See Fig. 9).
○ If the sleeve becomes loose during operation, tighten it
further. The tightening force becomes stronger when the
sleeve is tightened additionally.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by turning
it toward the left (in the counter-clockwise direction as
viewed from the front) (See Fig. 9).
Table 6
Use for drilling purpose.
Use the bit or socket matching the screw diameter.
Use after drilling a pilot hole.
Table 7
Clutch Dial
Position
LOW (Low speed)
For 4 mm or smaller diameter
1 – 22
screws.
For 8 mm or smaller nominal
diameter screws. (DS18DVF3)
For 6.2 mm or smaller nominal
diameter screws. (DS14DVF3)
1 –
For 5.8 mm or smaller nominal
diameter
DS9DVF3)
For 38 mm or smaller diameters.
(DS18DVF3)
For 30 mm or smaller diameters.
(DS14DVF3)
For 25 mm or smaller diameters.
(DS12DVF3)
For 21 mm or smaller diameters.
(DS9DVF3)
For drilling with a metal working drill
bit.
Suggestions
Rotating speed selection (Position of the shift knob)
screws. (DS12DVF3/
<For single sleeve chuck>
(1) Mounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front)
to open the clip on the keyless chuck. After inserting a
driver bit, etc., into the keyless drill chuck, and tighten
the sleeve by turning it toward the right (in the clockwise
direction as viewed from the front) (See Fig. 10).
○ If the sleeve becomes loose during operation, tighten it
further.
The tightening force becomes stronger when the sleeve
is tightened additionally.
(2) Dismounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front), and
then take out the bit, etc (See Fig. 10).
CAUTION
When it is no longer possible to loosen the sleeve, use a
vise or similar instrument to secure the bit. Set the clutch
mode between 1 and 11, and then turn the sleeve to the
loose side (left side) while operating the clutch. It should
be easy now to loosen the sleeve.
7. Confi rm that the battery is mounted correctly
English
HIGH (High speed)
For 6 mm or smaller diameter
screws.
For 4.8 mm or smaller nominal
diameter screws. (DS18DVF3)
For 3.8 mm or smaller nominal
diameter screws. (DS14DVF3/
DS12DVF3/ DS9DVF3)
For 24 mm or smaller diameters.
(DS18DVF3)
For 12 mm or smaller diameters.
(DS14DVF3/ DS12DVF3/DS9DVF3)
––––––––––––––––––––––
15