P Roduct Description; Intended Use; Scope Of Supply - df models Brushless SpeedHammer 4WD RC Monster Truck 1/8 Notice D'utilisation

3. P
roduct descrIPtIoN
The model is an all-wheel drive RC car chassis with a pre-installed brushless electric motor and a 2.4 GHz receiver station, a
programmed, electronic speed controller and steering servo with metal transmission. This model is intended both for opera-
tion on indoor tracks as well as operation outdoors.
The bodywork, which is ready-printed and cut out as well as the rear spoiler with a carbon look makes for a classy visual
impression, and the decals included can be used to customise your model.
The twin-deck chassis made of anodised aluminium is light-weight and torsion-resistant. The chassis obtains additional stur-
diness from a top deck made of anodised aluminium. Plastic shells bolted to the side of the chassis protect the installations
against spray water and flying rocks.
The two 2S LiPo rechargeable batteries (not part of the scope of delivery) enable symmetrical weight distribution by the
longitudinal axis and ensure immense power output. The impressive torque of the motor with intense acceleration can lead
backward overturning of the model. We recommend that beginners install the optional „wheelie bar" instead of the rear
bumper. A low-maintenance brushless motor provides satisfaction with higher power, greater torque and a higher efficiency
factor than conventional brushed motors. A heat sink with a fan attached ensures heat dissipation even under the most severe
conditions.
The unit is powered by the motor pinion on the centre differential. From there one drive shaft each made of metal meshes in
the encapsulated differentials of the front and rear axles, thus bringing about four-wheel drive. The differentials in the front
and rear axles provide for speed compensation between the wheel on the inside and the wheel on the outside of curves and
has metal gears. The model is entyrely ball-bearing-mounted.
A programmable electronic speed controller KL-80 with a fan attached is geared in optimum fashion to the brushless motor
and provides satisfaction through excellent starting behaviour, acceleration and excellent synchronisation.
The high-performance RS 90MGBB steering servo with metal gearbox and two ball bearings has high controlling torque
amounting to 88.3 Ncm and high control speed with maximum stability. A servo saver also provides protection for the servo
against sharp impacts against the wheels.
Anti-roll bars on front and rear axle each connect the bottom suspension arms of one axle in such a way, that the respective
other wheel is deflected along with a deflected wheel. The roll behaviour in curves of the vehicle is thus curbed and drivea-
bility improved.
In this 2.4 GHz remote control set with 2 channels, you have a radio control system that is ideally suited for primarily model
cars and model ships. Its proportional control channels allow 2 control functions to be remotely controlled independent of one
another. The 2.4 GHz transmitter and the receiver tuned to it do not work on a frequency predetermined by the transmitter
and receiver crystal. Each time they are switched on, the transmitter and receiver scan the frequency band for an available,
open frequency on which the radio link is then established.

.1 Intended use

This product has been designed solely for private use in the field of modelling and has operating times appropriate to this use.
This product is not approved either for commercial or industrial nor for continuous operation. Any improper use can result
in endangerment to people as well as damage to the product and dangers involved in such, like the loss of control over the
model, short-circuits, fires, electric shock, etc. Comply with the safety instructions in these Operating Instructions. They contain
important information on how to handle this product.
The product is suitable for children under 14 years only under adult supervision.

. Scope of supply

> A 4WD electric RC Monster Truck with:
• Twin-deck chassis made of anodised aluminium
• 4-disc rims with multi-spike wheels
• 4 infinitely variable aluminium oil-pressure shock absorbers.
• Monster Truck body and rear spoiler with carbon look,
cut-out and printed
• decals
• 2.4 GHz receiver, pre-installed and pre-adjusted
• Brushless electric motor with heat sink and fan, pre-installed
• Programmable, KL-80 electronic speed controller with fan,
pre-installed
• RS 90 MGBB steering servo, pre-installed
> 2.4 GHz 2-channel remote-control transmitter
> Communication plug
> USB cable for connecting the transmitter to the PC, for control-
ling simulation programs
> Operating Instructions for the model, the remote control unit
and the speed controller
Bedienungsanleitung / Operating Instructions / Notice d´Utilisation / Manual de Instrucciones / Istruzioni per l´uso
B s h
rushless peed ammer
4Wd rC m t 1/8
onster ruCk
N . 3221
o
mit 2,4 GHz 2Kanal Fernsteueranlage
with 2.4-GHz 2-channel remote-control transmitter
avec Radiocommande 2,4 GHz à 2 voies
con Emisora 2,4 GHz 2 canales de control remoto
con Trasmettitore a 2 canali 2,4 GHz
-  -