Product Familiarisation; Intended Use - Triton TBJ 001 Instructions D'utilisation Et Consignes De Sécurité

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18
Protect your hands
• Do not allow hands to get close to the cutting wheel or blades. Use a suitable push stick for
shorter workpieces with appropriate power tools
Be aware of others around you
• It is the responsibility of the user to ensure that other people in the vicinity of the work area
are not exposed to dangerous noise or dust and are also provided with suitable protective
equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded objects before cutting
• Do not attempt to cut material that contains embedded objects unless you know that the
cutting tool fitted to your machine is suitable for the job
• Walls may conceal wiring and piping, car body panels may conceal fuel lines, and long
grass may conceal stones and glass. Always check the work area thoroughly before
proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed from the cutting tool. It is the
user's responsibility to ensure that other people in the work area are protected from the
possibility of projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check that wrenches / adjusters
are removed prior to use
• Only use cutting tools recommended for your machine
• Do not attempt to modify cutting tools
• Ensure blades are sharp, in good condition and correctly fitted
• Do not attempt to resharpen blades that are not suitable for resharpening; these may
include specially hardened blades or blades made from hardened alloys typically containing
tungsten
• Blades that can be resharpened should be resharpened only according the blade
manufacturer's instructions. These may include a limited number of times the blade can be
resharpened
• Sharpened blades should be more thoroughly inspected before use and replaced
immediately if there is any doubt about their condition and suitability for use
• In the event blades encounter an embedded object in use that the blades are not suitable
for, blades should be replaced immediately
Direction of feed
• Always feed work into the blade or cutter against the direction of movement of the blade or
cutter
Beware of heat
• Cutting tools and workpieces may become hot in use. Do not attempt to change tools until
they have been allowed to cool completely
Control dust / swarf
• Do not allow dust or swarf to build up. Sawdust is a fire hazard, and some metal swarf is
explosive
• Be especially careful when cutting wood and metal. Sparks from metal cutting are a
common cause of wood dust fires
• Where possible, use a dust extraction system to ensure a safer working environment
GB
8

Product Familiarisation

1. Auxiliary Handle
2. Spindle Lock Button
3. Direction Indicator
4. Angle Lock
5. Face Centre Indicator
6. Fence Biscuit Edge Indicator (L)
7. Fence Blade Centre Indicator
8. Fence Biscuit Edge Indicator (R)
9. Non-Slip Pad
10. Depth Indicator
11. Turret Stop
12. Base
13. Depth Stop
14. Depth Stop Locking Nut
15. Dust Port
16. Motor Vent
17. On/Off Trigger Switch
18. Main Handle
19. Face
20. Handle Screws (x 4)
21. Blade Access Knob
22. Auxiliary Handle Bolt (x 2)
23. Click Stop (0°,45° & 90°)
24. Angle Scale
25. Angle Indicator
26. Centre Blade Indicator
27. Fence Height Scale
28. Blade Slot
29. Fence Locking Knob
30. Fence
31. Base Lid
32. Saw Blade
33. Threaded Blade Flange
34. Blade Tooth Tip
35. Direction Indicator
Accessories (not shown): pin spanner, dust bag, hex key & case

Intended Use

Portable hand-held mains-operated power tool with a small circular saw blade that cuts slots
into wood to create joints suitable for inserting various sizes of wood biscuits.

Publicité

Table des Matières
loading

Table des Matières