Front Panel Features - Numark DXMPRO Manuel D'utilisation

FRONT PANEL FEATURES

Microphone - Auxiliary Input Controls
1. "MIC – AUX GAIN" (Microphone - Auxiliary
Gain): This knob adjusts the volume of both
the main microphone and auxiliary inputs.
The gain should be turned completely to off
when connecting and disconnecting
equipment. If both inputs are used
simultaneously the inputs will be mixed
together.
2. "Treble" (Microphone - Auxiliary High EQ):
This knob adjusts the high-tone input sound of
the microphone.
3. "Bass" (Microphone - Auxiliary Low EQ): This
knob adjusts the low-tone input sound of the
microphone.
4. "Microphone" (Quarter Inch Microphone
Input): One microphone can be connected to
this Quarter Inch input terminal.
Primary Mixing Channel Controls
5. "Gain Knob" (Input Level Trim): This rotary
control adjusts the pre-fader input signal
levels of the inputs.
should be used with the pre-fader meter to
match levels of both input channels.
6. EQ:
"Treble" (Input Level High EQ): This rotary control
adjusts the high-tone sound of the inputs.
Turning the knob completely to the right
increases the level, turning the knob
completely to the left decreases the level to
This level adjustment
off. This music "KILL" control allows for
unique mixing styles.
"Middle" (Input Level Midrange EQ): This rotary
control adjusts the high-tone sound of the
inputs. Turning the knob completely to the
right increases the level, turning the knob
completely to the left decreases the level to
off. This music "KILL" control allows for
unique mixing styles.
"Bass" (Input Level Low EQ): This rotary control
adjusts the high-tone sound of the inputs.
Turning the knob completely to the right
increases the level, turning the knob
completely to the left decreases the level to
off. This music "KILL" control allows for
unique mixing styles.
7. "Phono(AUX)/Line Switch" (Input Selector
Switch): These three-position toggles select
what input source is engaged among the
connected units and a flash position to allow
rapid transforming effect. These toggles can
be rotated to suit your mixing preferences by
removing the top Mixer Panel and adjusting
their position.
8. "Input Level Slider" (VCA Fader): These slide
faders adjust the level for CH-1 or CH-2
respectively.
Note: This fader is user replaceable if it should ever
wear out. Simply remove the facepanel and
then remove the screws holding it in position.
Replace the fader with a quality authorized
replacement from your local Numark retailer.
9. "Slope Knob" (Input Fader Curve Style
Control): The position of this knob determines
the rate of volume level increase of the fader.
When turned to the left, the fader will
gradually fade in the volume as it is engaged.
When it is turned all the way to the right, a
very sharp fade of the volume will occur
immediately when the fader is engaged.
10. "Reverse Button" (Input Fader Reverse
Control): Activation of this switch can reverse
the fader direction.
Cueing / Monitor Controls
11. "Program/PFL Level Meter and Button":
Press to alternate display modes.
a) When PROGRAM is indicated, this meter
displays the stereo output levels of your
mixed signal.
b) When CH1 CH2 is indicated the meter
shows the peak, "PFL", Pre Fader levels of
channels 1 and 2. You can use the
channel "Gain" and "EQ" controls to
match the levels of input signals while
cueing
12. "Cue Gain Knob" (Headphone Level): This
rotary control adjusts the levels of the
headphones connected to the front panel
input.
13. "Cue Tone Knob" (Headphone Tone Control):
This rotary knob adjusts the tone of the
headphone output. The knob can be raised
and lowered to hide away by pressing it
down.
14. "Channel Cue Slider": Channels 1 and 2 can
be previewed using this mini-crossfader.
Sliding this to the left plays the left channel-
1 and sliding to the right plays the right
channel-2.
15. "Cue Button" (MIC and MASTER Cue
Buttons): When pressed, the CUE button
illuminates green indicating that the source
is being cued to the headphones.
you press Mic PFL it adds it to the cue mix.
When