Wolf ICBDF304 Instructions D'installation page 11

I N S TA L L AT I O N I N S T R U C T I O N S
A N T I - T I P B R AC K E T I N S T A L L A T I O N
This range can tip. Injury to persons
could result. Install the anti-tip bracket
supplied with the range.
Raise the unit to its desired height by adjusting
the front legs and rear casters. The legs and
casters allow for 54 mm height adjustment.
Use a 19 mm socket to adjust the rear casters.
The front legs are adjusted by rotating the
bottom hexagonal portion of the leg.
The anti-tip bracket can be installed by
securing it to the wall or floor using the
supplied hardware.
Refer to the chart and illustration below to
determine the proper distance from the left
side of the opening to the anti-tip bracket. This
will ensure the anti-tip bolt properly engages
the bracket.
M O D E L
762 mm Range 5 mm
914 mm Range 14 mm
1219 mm Range 5 mm
1524 mm Range 8 mm
ANTI-TIP
BRACKET
A
nti-tip bracket location. Wall anchor installation.
D R Y W A L L A P P L I C A T I O N S
fter properly positioning the anti-tip bracket,
use wall anchors to fasten it to the wall. Using
a Philips screwdriver or a low rpm screw gun,
drive the anchor into the surface of the wall-
board until the two cutting blades penetrate
the surface. Use gentle forward pressure to
rotate the collar until flush with the surface of
the wall. Refer to the illustrations below. Use
#8 screws and flat washers to fasten the anti-
tip bracket to the wall.
IMPORT NT NOTE: Pre-drill holes if difficulty
is encountered during installation of the wall
anchor. For hard wallboard or double-board
construction, use a 6 mm drill bit. For solid
plaster, use a 11 mm drill bit.
W O O D F L O O R A P P L I C A T I O N S
fter properly positioning the anti-tip bracket,
drill 5 mm pilot holes through the floor. Use
#12 screws and flat washers to secure the
A
bracket to the floor.
C O N C R E T E F L O O R A P P L I C A T I O N S
fter properly positioning the anti-tip bracket
drill 10 mm holes into the concrete a minimum
of 38 mm deep. Use 10 mm wedge anchors to
secure the bracket to the floor.
WALL
ANCHOR
ANTI-TIP
BRACKET
nti-tip bolt adjustment.
A N T I - T I P B O L T A D J U S T M E N T
Once the bracket is secured in place, adjust the
anti-tip bolt at the back of the range so the top
of the washer is 22 mm maximum from the
floor. Slide the range into the opening and
verify the anti-tip bolt is engaged. Refer to the
illustrations below.
IMPORT NT NOTE: The top of the range
must be level. Use the adjustable front legs
and the rear casters to level the range.
OV E N D O O R R E I N S T A L L A T I O N
IMPORT NT NOTE: The oven door(s) should
not be removed unless it is necessary to fit the
range through a tight doorway. Door removal
should only be done by a qualified service
technician or installer. Door removal and rein-
stallation may cause damage to the oven
porcelain interior.
Do not lift or carry the oven door by the
door handle.
ANTI-TIP
BOLT
22 mm
MAX
nti-tip bolt engaged.
If oven door(s) have been removed, follow
these steps to reinstall:
1) Hold the oven door on both sides and
position it with door hinges aligned with
openings in the oven frame.
2) Holding the oven door at an approximate
30° angle from vertical, slide the hinges into
the openings until the bottom hinge arms
drop fully into the hinge receptacles.
3) Open the oven door to its fully opened
position. Remove the hinge pin from the
appropriate hinge arm. Refer to the
illustration below.
4) Reinstall the hinge retainer plate with upper
and lower mounting screws.
5) Open and close the door completely to
ensure that it is properly installed.
6) For 1219 mm and 1524 mm ranges,
complete these steps for both oven doors.
7) Reinstall the lower kickplate assembly.
IMPORT NT NOTE: Fully extend the hinge
claw which is opposite the hinge pin location
and insert into the hinge pocket prior to insert-
ing opposite side. This will ease the installa-
tion of the oven door.
Hinge
Retainer Upper Mounting
Plate
Hinge
Pin
ANTI-TIP
DEVICE
ENGAGED
Kickplate
Oven door reinstallation.
Screw
11