Parker Hiross StarlettePlus SPS026-ES Manuel D'utilisation page 11

5 Control
QS Main power switch
UP button: press to increase the value of a selected parameter
DOWN button: press to reduce the value of a selected param-
eter, press for more seconds to force the drain to work.
esc
ESC button :returns to the previous level
SET button : one single press to see the alarms, press for more
set
seconds to ON/OFF the dryer
(illuminated) Dew point correct
(Flashing) warning dew point high/low
(off) alarm dew point
(illuminated) Condensate drain ON
(off) Condensate drain OFF
(illuminated) Dryer ON
(off) Dryer OFF / Dryer stand by
(illuminated) with compressor OFF
(illuminated) Allarm
(Led illuminated ) Maintenance
°C
(Led illuminated ) Grade
°F
Bar
(Led illuminated ) Pressure
PSI
English
5.1 Parameter settings
There are two levels of protection for parameters:
a) User (U): with immediate access, User-changeable;
b) Password protected Factory/Service (F/S): password required for ac-
cess; Factory/Service use only.
5.2 Condensate drain
Ii is possible to modify the operating modes of the drain, using the
"TIME" menu.
There are two operating modes:
a) TIMED (CHd = ON) - with draining at intervals and settable time;
in this confi guration keep pressed to force the drain to work;
b) EXTERN (CHd = OFF) - if there is an external drain.
Parameter table "TIME"
Code Defi nition
dON Time ON Drain (sec.)
dOFF Time OFF Drain (1=10 sec.)
CHd Confi guration drain
For choosing the set proceed as follows (or see the fl ow chart):
esc
set
Press buttons and together over 5 seconds to enter on sub-
menu.
Using buttons and select "Par" and press
Using buttons and select "TIME" and press
Using buttons and select the code to change and press
to confi rm.
Using buttons and change the value and press
esc
Press to exit.
In the same way it is possible to change interval and discharge times of
the drain.
5.3 Software menu
It is possible to see the software version and set the dryer for the remote
control or the supervisor in the menu "CF9".
Parameter table "CF9"
Code Defi nition
VER Software Version
SOFt Software type
rE On/Off remote
(Table 1)
SUP ON/OFF supervisor (Modbus)
SPS026 / SPS100-ES
Table 1
0 On/Off remoto disable
1 On/Off remote enable, local On/Off enable
2 On/Off remote enable, local On/Off disable
For choosing the set proceed as follows (or see the fl ow chart):
set
Press buttons
Using buttons
Using buttons
Using buttons
to confi rm.
Using buttons
Default Min Max.
esc
Press to exit.
5 1 60
12 2 270
Machine status
To get the machine status signal you have to connect to the following
OFF ON OFF
powered contacts (0-10V):
1) A1 on J3 on clamp A04
2) X1 on clamp GND
State ON (contact closed =10V)
set
State OFF (contact open = 0V)
to confi rm.
set Machine
to confi rm.
status
set
ON
OFF
set
to confi rm.
OFF
OFF
* in case of no power supply or loss.
Default Min Max.
1.0 --- ---
1 --- ---
0 0 2
OFF OFF ON
On/Off remote mode
esc
and together to enter on submenu.
set
and select "Par" and press to confi rm.
set
and select "CF9" and press to confi rm.
and select the code to change and press
set
and change the value and press
ON/OFF energy
power supply
display saving of alarms
YES ON
NO* ON
not
infl uent
YES OFF
NO* OFF
3 / 6
set
to confi rm.
presence
not
infl uent