Publicité
Les langues disponibles
Les langues disponibles
Safety
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential for
personal injury:
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which are
important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
1. Read this manual carefully. Failure to follow these
instructions could cause serious bodily injury and/or
property damage.
2. Check your local codes before installing. You must
comply with their rules.
3. Connect the pump to a separate circuit with no other
appliances on the circuit. Consult a licensed electrician
for all wiring.
NOTICE: This pump does not require a connection to a
main stack vent, per the National Standard Plumbing Code
(NSPC) 2003 Section 11.7.9.
Hazardous voltage. Can shock, burn or
cause death. Unplug pump before working on it.
DESCRIpTION
This pump is designed to be used with a sink where a
gravity drain line is not available. Attach the pump to the
drain tail piece; the pump will start when water begins to
drain. Uses include basement laundry sinks, wet bars and
utility sinks.
SpECIFICATIONS
Power supply required ...................................115V, 60 HZ.
Liquid Temp. Range ..................... 32° – 120°F (0° – 50°C)
Individual Branch Circuit Required (min.) .............15 Amps
Pump Inlet ......................................................... 1-1/2" NPT
Pump Discharge ................................................ 1-1/4" NPT
Fire or explosion hazard. Do not use in
explosive atmospheres. Pump fresh water only with this
pump. Use with salt water or brine will void the warranty.
California proposition 65 Warning
This product and related accessories
contain chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
INSTALLATION
(SEE FIgURES 1 AND 2)
Electric Shock Hazard. Plug pump into a
properly grounded, GFCI protected outlet. Do NOT plug
in the pump until after it is completely installed. Do not
remove or modify the grounding pins on the plugs.
Sink Bottom with Drain Port;
Tail Piece integral with Sink
A
1
2
For easier maintenance,
use 2 short sections of
pipe connected by a
1-1/2" Solvent Union.
3
1-1/2" Pump
Inlet Port
1-1/4" Pump
Discharge
Fittings Supplied:
A
Sink Drain Screen
B
1-1/4" NPT x 1-1/4" Slip Check Valve
C
1-1/4" NPT Ball Valve
Purchase Separately:
1
1-1/2" NPT x 1-1/2" Slip Female Adapter
2
1-1/2" Schedule 40 PVC Pipe, to fit
3
1-1/2" NPT x 1-1/2" Slip Male Adapter
4
1-1/4" NPT Galvanized Nipple (to fit)
5
1-1/4" NPT Galvanized Union
6
1-1/4" NPT x 1-1/4" Male Adapter
7
1-1/4" Schedule 40 PVC Pipe, to fit
8
1-1/4" Socket to Socket 90° Elbow
9
1-1/4" Schedule 40 PVC Pipe to Drain
PVC Pipe Cement
PTFE pipe thread sealant tape
1-1/2" Plastic Solvent Union
(For Drop Pipe – Optional)
NOTE: Be careful to avoid cross-threading;
Use only a plastic-compatible pipe-threading
compound or PTFE pipe thread sealant tape
when connecting threaded fittings to plastic adapters.
Figure 1: Typical method of mounting the pump.
4
5
6
7
Qty.
1
1
1
Qty.
1
1
1
1
1
2
4
1
As Needed
As Needed
As Needed
5798 0308
2
9
B
C
6
7
8
Publicité
