Technical Data; Possible Problems; Guarantee - ATIKA ASP 10 N - 400 Notice Originale

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
T
e
c
h
n
i
c
a
l
d
a
t
a
T
e
c
h
n
i
c
a
l
d
a
t
a
Model / Type
Splitting force
Log length
Log diameter
Stroke
Feed speed
Return speed
Hydraulic oil (max.)
Hydraulic pressure
Electric motor performance (power consumption)
Power supply
Dimensions
Weight
P
o
s
s
i
b
l
e
p
r
o
b
l
e
m
P
o
s
s
i
b
l
e
p
r
o
b
l
e
m
Before each fault clearance:
− switch off device
− pull out main plug
Problem
Logs are not being split
properly
(insufficient splitting
performance).
Splitting
column
moves
unsteadily or with strong
vibrations.
Splitting column does not
move in.
Motor starts, but splitting
column does not move in.
Motor will not start.
G
u
a
r
a
n
t
e
e
G
u
a
r
a
n
t
e
e
Please observe the enclosed terms of guarantee.
s
s
Possible cause
⇒ The log is not positioned correctly.
⇒ The log exceeds the maximum dimensions or
the wood is too hard for the performance of
the machine.
⇒ Splitting blade does not split log.
⇒ Hydraulic pressure too low.
⇒ Release rods bent (hydraulic tappet not quite
pressed in).
⇒ Incorrect connecting lead (longer than 10 m or
too small cable cross-section).
⇒ Air in the circuit.
⇒ Splitting column not sufficiently lubricated or
oiled.
⇒ Hydraulic pump defective.
⇒ Motor turns in wrong direction
⇒ No electrical power.
⇒ 2-phase mode in threephase motor.
⇒ Connection cable defective.
⇒ Electric motor defective.
ASP 10 N – 400
100 kN (10 t)
max. 1300 mm
min. 50 mm – max. 400 mm
≈ 520 mm
approx. 0.05 m/sek.
approx. 0.25 m/sek.
10 litres
21.4 MPa (214 bar)
P
4.0 kW (S6 40%)
1
400 V 3~ 50 Hz, 16 A
length 580 x width 530 x height 1530 mm
approx. 175 kg
Remedy
⇒ Reposition the log correctly.
⇒ Cut
the
log
⇒ Sharpen splitting blade, check for burrs or notches.
⇒ Check the oil level and add more oil if necessary.
If the problem cannot be rectified, refer to the
manufacturer or other approved service centre.
⇒ Arrange for manufacturer or authorised company to
adjust the rods.
⇒ Use the correct connecting lead.
⇒ Check the oil level and add more oil if necessary.
⇒ Lubricate splitting column or oil with environmentally
friendly spray oil.
If the problem cannot be rectified, refer to the
manufacturer or other approved service centre.
⇒ To correct the problem, refer to the manufacturer or
other approved service centre.
⇒ Check the motor direction
Threephase: adjust the motor direction
⇒ Check the fuse.
⇒ Have fuse and lead checked by qualified electrician.
⇒ Replace the connection cable or have it checked by an
electrician.
⇒ To correct the problem, refer to the manufacturer or
other approved service centre.
to
the
required
dimensions.
29

Publicité

Table des Matières
loading

Table des Matières