Cardin Elettronica SL Série Mode D'emploi page 20

REMOTE CONTROL (fig. 3 page 4)
The system can be remotely activated using radio control devices. Each chan-
nel can be set to a maximum of 2 functions:
- function 1: sequential command
- function 2: limited opening or blocking button
To set one of the functions to the channels A-B-C-D use the selection jump-
J1
A
B
1
2
block open-close
Memory module (M1)
This is extractable, furnished with a non volatile EEPROM type memory and
contains the transmitter codes and allows you to memorise up to 300 codes.
The programmed codes are maintained in this module even during blackouts.
Before memorising the transmitters for the first time remember to cancel the
entire memory content.
If the electronic card has to be replaced due to failure, the module can be
extracted from it and inserted into the new card. Make sure that the module
is correctly inserted as shown in fig. 3.
Signal LEDs "L3" (fig. 3):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (fig. 3):
2. At the same time activate the transmitter which is to be memorised.
P1 MEMO
4. Release the button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the channel
is different or it is a different transmitter the memorisation attempt will abort
without success).
that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory: if you
attempt this, the LED will switch off when you activate the transmitter (point
the memorising procedure.
If after activating the transmitter for the first time you wait for more than fifteen
seconds without activating the transmitter a second time the memorisation
attempt will abort without success.
Cancelling a channel (fig. 3):
quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED will remain lit for 2 s, indicating that the transmitter has been can-
celled.
Note: If the user that you wish to cancel is not in memory, the LED will stop
cancellation procedure.
For both the memorisation and cancellation procedures, if the button is released
before activating the transmitter the procedure will abort.
Cancelling all user codes from memory (fig. 3):
L3
onds).
L3
Note: When the memory is almost full the time required to search for a user
code could take up to 1 second from when the command was received. If led
"L3" remains lit memory is completely full. To memorise a new transmitter you
will first have to cancel a code from memory.
TD;
TAL or TB.
J3
TB;
TAL;
1 open-block-close-
P1 MEMO L3
L3
L3
P1 MEMO will you be able to continue
P2 L3
P2
P1+P2
Memorising ulterior channels via radio
J2
already been memorised in the receiver, press the button in the transmitter
as shown in the figure.
Note: all the receivers within range when the
channel button is pressed (and which have at
least one of the transmitter channel buttons
memorised) will activate their signal buzzer
B1
3. Press one of the channel buttons on the same transmitter. The receivers
and will then deactivate.
The receivers which contain the channel code will sound a one-second long
4. Press the previously chosen channel buttons on the transmitter which you
after which the receiver will be ready to receive another code.
5. To leave the programming mode wait for 3 seconds without pressing any
buttons.
programming mode.
Note: When the memory is entirely occupied the buzzer will sound 10 rapid
L3
when the memory is full.
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58 (impedance
50 ) with a maximum length of 15 m.
FUNCTION MODE
1) Automatic
door is completely closed the opening command will start a complete cycle
which will end with automatic reclosing and the night light switching off.
Automatic reclosing starts after the programmed pause period has elapsed
when the opening cycle has been completed or straight away after the inter-
vention of a photoelectric cell (the intervention of a photoelectric cell causes
the pause time to be reset).
During the pause time the symbol
the blocking button during this period will stop automatic reclosing and con-
sequently stop the display from flashing.
The indicator light remains lit until the closing manoeuvre has terminated.
2) Semiautomatic
cycle control using separate opening and closing commands. When the door
has reached the completely open position the system will wait until it receives
a closing command either via an external control button or via radio control,
before completing the cycle. The indicator light remains lit until the closing
manoeuvre has terminated.
3) Manual manoeuvre
This can be used to close the gate (or open it) under the direct control of the
9
This mode is only active after you have programmed the system. In this mode
the safety devices FTCI, CSP and TB only work when they are in alarm.
-
The motor will block in the closing direction due to:
TC
- activating the inverting photocells (FTCI) or the safety edge (CSP).
20
J2
programming via radio" mode.
Description :
Drawing number :
DM0531
Product Code : RCQ449100
Draft : P.J.Heath Date : 13-04-2001
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/4018
programming via radio
programming via radio
2 ON
will flash on the display and pressing
2
ON
TC
TB
TC
-
MEMORIZZAZIONE CODICE TX-RX
OFF