Melitta LOOK Perfection Mode D'emploi page 7

Hardness setting
°dH
Flash rhythm
CALC button 
Table 1
Warming time setting
Flash rhythm
button 
ON/OFF
Table 2
factory settings the CALC button flashes briefly four
times with the following pauses ............
• You can set the water hardness at three further
levels. Each time you briefly press the CALC button
 the display changes to flashing one, two or three
times, each time followed by a pause
(......, ......, ......).
• The settings and display are shown in the following
table 1.
• Once you have set the desired hardness level, again
hold the CALC button  down for longer than two
seconds. The light goes off and your settings are
saved.
Please note:
• Water hardness cannot be programmed while
brewing.
• The last water hardness level chosen remains even
after removing the power cable.
4. Setting the hotplate
Keeping coffee warm on the hotplate affects the taste
of your coffee. To avoid this you should enjoy your
coffee fresh by drinking it as soon after brewing as
possible. Unnecessary warming also uses valuable
energy. The factory settings for the appliance are for
40 minutes of warming. After this the hotplate turns
off automatically. This time can be changed as needed:
• Press the ON/OFF button  longer than two seconds.
• In the factory settings the ON/OFF button  flashes
briefly twice with the following pause (......).
• There are two other settings for the warming time.
By briefly pressing the ON/OFF button  the
display changes to flashing three times or once, each
time followed by a pause (......, ......, ......).
• The settings and display are shown in table 2.
• Once you have set the desired warming time,
confirm your settings by pressing the ON/OFF
button  for longer than two seconds. Your settings
are now saved
• The last setting chosen remains even after removing
the power cable.
5. Making coffee
• Ensure that the appliance is connected to the power
source.
1
2
<7°
7-14° dH
dH
............ ............
20 minutes
40 minutes
............ ............
3
14-21°
dH
............
60 minutes
............
• Fill the water tank.
• Remove the detachable water tank by holding the
recessed grip and pulling straight up .
• Remove the water tank lid and fill with the desired
amount of fresh water from the tap. Using the water
level indicator on the tank you an choose the cor-
rect number of cups.
• Close the tank by replacing the lid and insert the
tank back in the appliance. Please ensure that you
replace the tank upright in the appliance. The guide
rails on the appliance (left of the tank) will help you
with this .
• Alternatively use the glass jug to pour the water into
the tank in the appliance . The required amount
of water can be seen on the water level indicator on
the tank.
Small cup symbol = approx. 85 ml coffee per cup,
large cup symbol = approx. 125 ml coffee per cup.
• Close the lid on the water tank and place the glass
pot with closed lid in the appliance.
• Open the swivel filter  to the left.
filter bag 1x4
• Fold a Melitta
®
and place it in the filter holder . Press the filter
bag into the filter holder by hand, to ensure a good
fit.
• Put the ground coffee into the coffee filter. We
recommend using 6 g of coffee per large cup at a
medium setting of the AromaSelector
• A lternatively, you can vary the taste of the coffee
according to your personal preference using the
same quantity of coffee. For a milder coffee, turn
the AromaSelector to the left ( ). For a stronger
®
coffee, turn it to the right (
• Turn the appliance on . Brewing begins.
• After making your coffee the hotplate will keep it
warm and will turn off automatically after the time
you have set (see point 4). This avoids unnecessary
use of electricity and saves energy. You can of course
turn the machine off manually at any time.
• The drip stop prevents your coffee from dripping,
when you remove the pot from the appliance .
• With the help of the detachable inner filter you can
dispose of the filter bag simply and easily .
6. Cleaning and maintenance
External cleaning
• Switch off the machine before cleaning and disconnect
4
>21°
dH
............
GB
at the embossed seam
®
.
®
).
9