Bluetooth Mode; Usb Mode - PERFECTPRO Handsfree 2 Mode D'emploi

Bluetooth Options
The Bluetooth function can be set to operate in different ways as below:
1. In Bluetooth mode, press the Menu button to enter the system setting.
2. Rotate the Tuning knob until "Bluetooth" is displayed; press the Tuning knob.
3. Rotate the Tuning knob to select "BT always on", "BT mode only" or "Disconnect
BT" options, and press the Tuning knob to select the setting.
a. BT always on Bluetooth is turned on when the Handsfree radio is on. You
can playback music in the Bluetooth mode and use the
Hands-Free-Calling feature to answer incoming phone calls
in all operation modes, for example, also when you are
listening to the radio. As an indication, the blue Bluetooth
connected LED will be on in all operation modes (FM, DAB,
Bluetooth and AUX IN).
b. BT mode only Bluetooth is turned on only in Bluetooth mode. You can
playback music and use the Hands-Free-Calling feature to
answer incoming phone calls in the Bluetooth mode only.
As an indication, the blue Bluetooth connected LED will be
on only in the Bluetooth mode.
c. Disconnect BT Bluetooth will be disconnected from your mobile phone
and enter the "discoverable mode" (The blue Bluetooth
connected LED will start blinking until a new pairing is
established). This is to allow the Bluetooth pairing to another
device. If no new device is paired, the Bluetooth will
automatically try to connect to the last device when it is
switched off and on again.
Note: The volume settings of your mobile phone influence the volume of the music
streaming and the volume of the incoming phone calls on the Handsfree radio.
The Auto-Power management function will be activated in Bluetooth mode. If there is
no signal from Bluetooth for a period of over 15 minutes, the Handsfree 2 radio will
automatically switch to standby mode. Pressing the On/Off button will wake up the unit.
Bluetooth LED configuration
1. Press the On/Off button to turn on the radio.
2. Press the Menu button, and then rotate the Tuning knob until the display shows
"System".
3. Press the Tuning knob; rotate the Tuning knob until the display shows "Bluetooth
LED".
4. Press the Tuning knob to enter the Bluetooth LED adjustment menu.
5. Rotate the Tuning knob to select "on" (by default) in order to keep Bluetooth LED
lightened when connected;
6. Or rotate the Tuning knob to select "off" to turn off Bluetooth LED when Bluetooth
connection has been established.
7. Press the Tuning knob to confirm your choice.
15

USB MODE

CONDITIONS TO PREVENT MOIST FROM ENTERING THE RADIO!! KEEP THE
RUBBER COVER CLOSED UNDER THESE CONDITIONS.
USB memory devices can be used with the radio for playback of MP3, AAC, FLAC and
WAV files.
The radio has been tested with a range of USB memory devices up to 32GB. However,
there are many different USB memory device variants available and not all of them can
be guaranteed to work in this radio. Memory must use the FAT or FAT32 filing system in
order to operate in this radio.
Audio formats supported for playback are MP3, AAC, FLAC and WAV. Playback does
not support files that have DRM protection.
The USB socket are located on the side behind the rubber cover. Make sure the rubber
cover is closed well after use to prevent moist and dirt from entering the radio.
The USB memory device should not be removed during playback as damage or
corruption of files may occur.
USB memory devices are not included with this radio.
Note: When the radio is playing a USB stick, due to additional power consumption
of this, the charging of the batteries will stop in order to maintain normal functioning
and quality of the USB playback. Once the USB stick is removed normal charging will
continue.
Insert and remove a USB memory device
Carefully insert a USB memory device into the USB socket.
To remove the USB memory device, simply pull the device out.
Playing music files
1. Press the On/Off button to turn on the radio.
2. Press the Source button to select the USB.
The display shows "READING". It may take some time before the radio has read in
the folders and files data on the memory device.
3. After reading the USB memory device, the radio will start to play the first file (song)
in the first folder.
If no USB memory device is inserted, the display will show "NO USB STICK"
respectively.
4. To pause the playback, press the Play/Pause button.
Press the Play/Pause button again to resume the playback from pause position.
5. To skip to the next file, press the Fast Forward button.
6. To skip to the previous file, press the Rewind button
7. While the file is playing, press and hold down either the Fast Forward button or
Rewind button. Release the button when the desired part of the file is reached.
8. To skip to the next folder, presses the Folder + button.
9. To skip to the previous folder, presses the Folder + button.
GB
GB
16