Publicité
Les langues disponibles
Les langues disponibles
EN
Gratulation for your SEAWIND by Staufenbiel.
We are aware of, that there are plenty different ways of buliding up or setting up a model. These
Before starting to build, inspect the parts to make sure they are of acceptable quality. If any parts are missing
Before starting to build, inspect the parts to make sure they are of acceptable quality. If any parts are missing
are not of acceptable quality, or if you need assistance with assembly, contact Product Support. When reporting
Manual is just a sample of how you can build it.
are not of acceptable quality, or if you need assistance with assembly, contact Product Support. When reporting
defective or missing part, use the part names exactly as they are written in the Kit Contents List.
defective or missing part, use the part names exactly as they are written in the Kit Contents List.
01. Fuselage
..........................................................x1
01. Fuselage
..........................................................x1
Please read this manual carefully before start assembling the modell.
02. Left Wing
..........................................................x1
02. Left Wing
..........................................................x1
03. Right Wing
........................................................x1
03. Right Wing
........................................................x1
04. Horizontal Stabilizer
..........................................x1
04. Horizontal Stabilizer
..........................................x1
05. Fin Tip
..............................................................x1
05. Fin Tip
..............................................................x1
06. Propeller
..........................................................x1
06. Propeller
..........................................................x1
07. Propeller Adapter
..............................................x1
07. Propeller Adapter
..............................................x1
08. Spinner
.................... ........................................x2
08. Spinner
.................... ........................................x2
09. Carbon Rod
......................................................x1
09. Carbon Rod
......................................................x1
10. Left Landing Gear
..............................................x1
10. Left Landing Gear
..............................................x1
11. Right Landing Gear
............................................x1
11. Right Landing Gear
............................................x1
Replacement Par ts List
Replacement Par ts List
Replacement part for the ST MODEL SeaWind are available using the numbers in the Replacement Parts List
Replacement part for the ST MODEL SeaWind are available using the numbers in the Replacement Parts List
that follows.
that follows.
Order NO.
Description
Order NO.
Description
ST 141
40AMP U-BEC ESC
ST 141
40AMP U-BEC ESC
ST 112
11.1V Lipo 2200mAh Battery
ST 112
11.1V Lipo 2200mAh Battery
ST 172
ST6DF 2.4Ghz 6CH Transmitter
ST 172
ST6DF 2.4Ghz 6CH Transmitter
ST 180
ST6DF 2.4Ghz 6CH Receiver
ST 180
ST6DF 2.4Ghz 6CH Receiver
ST 204
11x8 Propeller
ST 204
11x8 Propeller
ST 121
9g Servo
ST 121
9g Servo
Attention: Pictured transmitter, battery and charger are not included!
ST 122
17g Servo (P)
ST 122
17g Servo (P)
ST 124
36g Servo
ST 124
36g Servo
NEEDED TOOLS AND EqUIPMENT
TOOLS REQUIRED
TOOLS REQUIRED
Sharp Hobby Knife
Sharp Hobby Knife
≥85mm
≥85mm
Needle Nose Pliers
Flathead Screwdrivers (size:M,S)
Needle Nose Pliers
Flathead Screwdrivers (size:M,S)
12
PREFACE
INTRODUCTION
INTRODUCTION
12. Screw (M2.5x14)
...............................................x1
12. Screw (M2.5x14)
...............................................x1
13. Screw (M3.0x16)
........................... ....................x1
13. Screw (M3.0x16)
........................... ....................x1
14. Screw (M2.5x10)
...............................................x6
14. Screw (M2.5x10)
...............................................x6
15. Battery Pack
.....................................................x1
15. Battery Pack
.....................................................x1
16. "Y" Servo Extension
...........................................x2
16. "Y" Servo Extension
...........................................x2
17. Charger
............................................................x1
17. Charger
............................................................x1
18. Transmitter
.......................................................x1
18. Transmitter
.......................................................x1
19. Decals
.............................................................x1
19. Decals
.............................................................x1
20. Instruction
............................................... .........x1
20. Instruction
............................................... .........x1
21. Sucking Bottle
..................................................x1
21. Sucking Bottle
..................................................x1
SET CONTENT
Order NO.
Description
Order NO.
Description
ST 185
Servo Speed Reducer (SSR)
ST 185
Servo Speed Reducer (SSR)
ST 160
3S Lipo Smart Balancing Charger
ST 160
3S Lipo Smart Balancing Charger
STSE 010
Fuselage Set
STSE 010
Fuselage Set
STSE 020
Wing Set
STSE 020
Wing Set
STSE 030
Staibilizer
STSE 030
Staibilizer
STSE 040
Tip Fin
STSE 040
Tip Fin
STSE 050
Landing Gear (L&R)
STSE 050
Landing Gear (L&R)
STSE 011
Brushless Motor
STSE 011
Brushless Motor
Ruler
Ruler
Hex Wrench
Hex Wrench
Awl
Awl
www.sheng-teng.com
www.sheng-teng.com
Mount the landing gears to both side of fuselage using six M2.5x10mm. Pay attentin to the marks
"L" & "R" on the bottom of the landing gears. The "L" landing gear should be mounted in left side
of fuselage; The "R" landing gear should be mounted in right side of fuselage.
01
HORIZONTAL STABILIZER INSTALLATION
Fit the horizontal stabilizer onto the fin. Then lock it with M3.0x16mm screw. Guide the pushrod
into the screw-lock connector on elevator horn, and lock it to avoid loosening.
03
Attach the fin tip onto its foundation on the top of fin as illustration.
Slide the fin tip to the end to avoid loosening.
05
1
1
LANDING GEAR INSTALLATION
02
04
06
EN
13
Publicité
