Festool CMS-GE Notice D'utilisation D'origine/Liste De Pièces De Rechange page 10

CMS-GE
GB
5 Assembly
Ensure that the floor around the ma-
chine is level, in good condition and
free of loose objects (e.g. chips and offcuts).
The CMS-GE can be set up with or without
the legs folded out (Fig.
To fold out the legs, open the four rotary
knobs [2-3] as far as they will go. After fold-
ing out the legs, retighten the four rotary
knobs.
So that the machine stands securely, the
length of one of the legs can be changed by
turning the cap on the end [3-4].
When collapsing the base, fold up pair of legs
[3-6] first and then the second pair of legs
[3-5].
6 Power supply and start-up
WARNING
Unauthorised voltage or frequency!
Risk of accident
The mains voltage and the frequency of
the power source must correspond with
the specifications on the machine's name
plate.
In North America, only Festool machines
with the voltage specifications 120 V/60
Hz may be used.
For safety reasons, only plug the power
plug [3-3] into totally earthed socket.
Only use extension cables with ground
wire.
On completion of your work, wind the
power cable around the holders [3-7].
The switch-/socket-unit
age supply and as ON-/OFF-switch of a pow-
er tool build into the CMS-GE.
Plug the plug of the mains
tally earthed socket.
Connect the power tool, bulit into the
CMS-GE, to the socket [3-2].
To switch ON press the green button
1].
To switch OFF press the red button [2-2].
The switch-/socket-unit has a zerovoltage
release. This prevents a recurrence of the
voltage following a power cut (e.g. blackout).
After a power cut press the green button
1] again to switch ON .
10
[2] + [3]).
[3-1] serves as volt-
[3-3] into a to-
[2-
[2-
7 Accessories
Use only original Festool accessories and
Festool consumable material intended for
this machine because these components are
designed specifically for the machine. Using
accessories and consumable material from
other suppliers will most likely affect the
quality of your working results and limit any
warranty claims. Machine wear or your own
personal workload may increase depending
on the application. Protect yourself and your
machine, and preserve your warranty claims
by always using original Festool accessories
and Festool consumable material!
The order numbers of the accessories and
tools can be found in the Festool catalogue or
on the Internet under "www.festool.com".
7.1 Schalterabdeckung (accessory)
A switch guard (CS 70 SA) can be fitted to
the switch casing to prevent the device from
being switched on without authorisation. The
switch cover can be secured with a padlock.
8 Disposal
Do not throw the power tool in your house-
hold waste! Dispose of machines, accesso-
ries and packaging at an environmentally re-
sponsible recycling centre. Observe the valid
national regulations.
EU only: European Directive 2002/96/EC
stipulates that used electric power tools must
be collected separately and disposed of at an
environmentally responsible recycling cen-
tre.
9 Warranty
We offer a warranty for material and produc-
tion defects for all our tools in accordance
with the locally applicable legal provisions,
but for a minimum of 12 months. Within the
EU member states, the warranty period is 24
months (verification through invoice or deliv-
ery note). Damage caused by the operator,
natural wear, overloading, incorrect handling
or through the use of the equipment not
specified in the operating manual, or damage
which was known at the time of purchase, is
not covered by the warranty. Furthermore,
damage caused by the use of non-original
accessories and consumable materials (e.g.
sanding pads) is also excluded.