Elite Real Turbo Muin B+ Mode D'emploi page 24

EN
2) Turn the adjusting nut half a turn to tighten the
belt correctly (Pic. 34).
NOTE: if the belt is still uneven after performing
this operation, repeat step 2) and retest.
3) Tighten the adjustment locking screw (under point
1) by one full turn to set the adjustment (Pic. 35).
WARNINGS
• Real Turbo Muin B+ becomes hot during use.
Wait for it to cool before touching the resistance
unit covers.
• Use the Real Turbo Muin B+ trainer as descri-
bed in the manual.
• Real Turbo Muin B+ is not equipped with an
emergency brake.
• Real Turbo Muin B+ has been designed and ma-
nufactured to ensure maximum safety of the user
and/or third parties, but people, children and pets
should be kept away from the trainer during use
as contact with the moving parts of the trainer and
the bicycle may result in damage or injury.
• Never put your fingers or foreign objects of any
kind through the slots on Real Turbo Muin B+, as
there will be high risk of damage to the trainer
and/or serious physical injury.
• Before you start training, place the trainer in a
suitable location, away from any potentially dan-
gerous objects (furniture, tables, chairs...) so as to
avoid any risk of accidental or inadvertent contact.
• The Real Turbo Muin B+ is to be used by only
single rider at a time.
• The max weight limit of the user is 113 kg / 250
lb in accordance with the referenced norm EN
957-1 Class HC.
• Always check the safety and stability of the
bicycle on Real Turbo Muin B+ before training.
• No part of the product has any use beyond its ori-
ginal application. The warranty will be void if the
unit has been opened or tampered with.
• Since the feet are made of soft non-slip mate-
rial, they may leave traces of rubber on the floor
during use.
• If the trainer needs to be shipped for technical
support and/or any other reason, it must be ship-
ped in its original box. Damage due to a failure to
use the original packaging is not covered by the
warranties.
24
Note: before shipping your trainer or any of its
parts for technical support, you must first consult
Elite or its distributor or your dealer. Any items
received without prior agreement will be rejected
• Do not leave the charger plugged in while not in
use.
• Do not store the Real Turbo Muin B+ in cold
and damp places. This may damage its electronic
components.
• Use only the supplied charger.
• The Real Turbo Muin B+ compliance with EU
laws (see "declaration of compliance", page 62)
may be voided if a charger different from the ori-
ginal is used.
TROUBLESHOOTING
• What to do before running the software?
Connect the USB ANT dongle, power up the trai-
ner (or if in sleep mode, just pedal for a few se-
conds in order to wake it up) and touch a key of the
console to wake it up. Then launch the software.
• The PC does not recognize the USB ANT dongle
("Dongle ANT not found" error).
Verify that the dongle is correctly connected to a
USB port of the PC.
Install properly the USB ANT dongle driver (see
procedure).
If the dongle and driver are correctly installed
but the program doesn't recognize the USB ANT
dongle, then remove the USB ANT dongle and
re-connect it to the same USB port, then run the
software again.
• The trainer doesn't connect ("Real Turbo Muin
B+ not found" error)
Be sure the trainer is connected to the power
supply.
If the trainer has been connected to the power
supply for more than 2 minutes (and hasn't been
used), then it will go to sleep mode. Pedal for a
few seconds to wake it up. Then run the software.
If it still doesn't connect, then probably the Device
Trainer Number hasn't been set correctly. Check
if the Device Trainer Number is correct, using the
"Settings-Edit Trainer Number..." menu. Check if
the value matches the value on the trainer. Then
re-start the software.
If the software still doesn't connect to the trainer,