IMG STAGELINE PARL-30SPOT Mode D'emploi page 8

DMX LED Spotlight
These instructions are intended for installers of the unit
and for users with basic knowledge in DMX control .
Please read the instructions carefully prior to operation
and keep them for later reference .
All operating elements and connections described
can be found on page 2 .
1 Operating Elements
and Connections
1.1 Spotlight
1 Locking screws for the mounting bracket (9)
2 Connection jack for the remote control LC-3
3 DMX signal output (3-pole, XLR) for connection
to the DMX input of another DMX light effect
unit;
1 = ground, 2 = DMX−, 3 = DMX+
4 DMX signal input (3-pole, XLR);
1 = ground, 2 = DMX−, 3 = DMX+
5 Button for adjusting the DMX address
(see chapter 7 .2)
6 Mains cable for connection to a socket
(230 V/ 50 Hz)
7 Mounting plate for fixing the spotlight to a wall
or ceiling
8 Screw for the mounting plate
9 Mounting bracket
10 Housing cover with plastic pane
11 Locking screw for the latch (12)
12 Latch for the housing cover
1.2 Remote control LC-3
The remote control is available as an accessory and
not supplied with the LED spotlight .
13 Button STAND BY for the function Blackout
(light off)
14 Button FUNCTION for selecting various light
changing functions depending on the operating
mode selected with the button MODE
15 Button MODE for switching over between
Sound mode 1
Manual mode
Sound mode 2
Auto mode
Note: For control via the remote control, there must be
no DMX signal at the input DMX IN (4) .
8
(LED off)
(LED on)
(LED flashing slowly)
(LED flashing rapidly)
2 Safety Notes
The spotlight corresponds to all relevant directives of
the EU and is therefore marked with
WARNING The spotlight is supplied with hazar-
dous mains voltage . Leave servic ing to
skilled personnel only and do not insert
anything into the air vents, otherwise
you will risk an electric shock!
•
The spotlight is suitable for indoor use only . Protect
it against dripping water, splash water and high
humidity . The admissible ambient temperature
range is 0 – 40 °C .
•
Immediately disconnect the mains plug from the
mains socket
1 . in case of visible damage to the unit or to the
mains cable,
2 . if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3 . if malfunctions occur .
In any case the unit must be repaired by skilled
personnel .
•
A damaged mains cable must be replaced by skilled
personnel only .
•
Never pull the mains cable for disconnecting the mains
plug from the mains socket, always seize the plug .
•
For cleaning only use a dry, soft cloth, never use
chemicals or water .
•
No guarantee claims for the spotlight and no lia-
bility for any resulting personal damage or material
damage will be accepted if the spotlight is used for
other purposes than originally intended, if it is not
safely mounted or correctly operated, or if it is not
repaired in an expert way .
•
Important for U. K. Customers!
The wires in this mains lead are coloured in accord-
ance with the following code:
green / yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
1 . The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
, or coloured green or green and yellow .
2 . The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black .
3 . The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red .
Warning – This appliance must be earthed.
.