Cembre RHU 131 Notice D'utilisation Et Entretien page 6

ENGLISH
5.4) Dies, indentors, pre-rounding dies - fi tting and removal
– The containing die (96) and upper pre-rounding die (95): are located in the adaptor AU130-...
(98) by grooves in the upper face.
– The lower pre-rounding die (94): is inserted or removed from the adaptor AC130-P (91), by pulling
the release button (92).
– The indentor PS130.../E (93): is inserted into the seat on the ram (09) (see § 4.3.2).
6. MAINTENANCE
The head is robust and requires very little daily maintenance.
Compliance with the following points should help to maintain the optimum performance of the tool.
6.1) Accurate cleaning
Dust, sand and dirt are a danger for any hydraulic device.
Avoid putting the head on muddy or dusty ground. Any dirt particles may score the ram and create
oil leaks.
Every day, after use, the head must be cleaned with a clean cloth, taking care to remove any residual
particles, especially around the moving parts.
6.2) Replacement of the automatic coupler
Use a 22 mm spanner to unscrew the old coupler:
– Remove the obsolete coupler.
– Carefully clean the thread to remove the old sealant.
– Apply Tefl on tape to the thread.
– Fit the new automatic coupler and tighten to 30 Nm (22 lbf ft).
The oil pressure in the head must always be completely released before disconnecting the head
from the hose.
6.3) Storage
(Ref. to Fig. 1)
When not in use, the head should be stored and transported in it's case to prevent damage. Fol-
lowing cases are available:
– VAL P26 plastic case; size 445x290x115 mm (17.5x11.4x4.5 in.); weight 1,2 kg (2.65 lbs), for storage
of the head and 14 sets of semi-circular slotted dies.
– VAL 130-U steel case; size 450x305x80 mm (17.7x12x3.15 in.); weight 5 kg (11 lbs), for storage of
the head, semi-circular slotted dies and accessories for crimping aluminium connectors.
– VAL 130 steel case; size 360x280x48 mm (14.17x11x1.89 in.); weight 3 kg (6.62 lbs), for storage
of the accessories for crimping aluminium connectors.
7. RETURN TO Cembre FOR OVERHAUL
In the case of a breakdown contact our Area Agent who will advise you on the problem and give
you the necessary instructions on how to dispatch the tool to our nearest service Centre; if possible,
attach a copy of the Test Certifi cate supplied by Cembre together with the tool or fi ll in and attach
the form available in the "ASSISTANCE" section of the Cembre website.
(Ref. to Fig. 5)
6
8. LISTA DEI COMPONENTI
(Rif. a Fig. 6)
N° Codice Part. DENOMINAZIONE
6120123 01 CILINDRO
6700250 02 ANELLO ELASTICO ø 36
6170140 03 COPERCHIO MOLLA
6360420 04 GUARNIZIONE OR
6040320 05 ANELLO BK
6520620 06 MOLLA ESTERNA RICH. PIST.
6520610 07 MOLLA INTERNA RICH. PIST.
6300040 08 FUNGO
6620315 09 PISTONE
6522006 10 MOLLA PISTONCINO
6620320 11 PIST.FERMA MATRICE PIST.
6620445 12 PIST.SBLOCCA MATRICE PIST.
6760040 13 SPINA ELASTICA ø 3x8
6280025 14 FORCELLA
I particolari indicati con ( ) sono quelli che la Cembre consiglia di cambiare sempre nel caso di un eventuale
smontaggio della testa.
Detti particolari sono fornibili su richiesta nella "Confezione Ricambio per RHU131".
La garanzia decade qualora vengano utilizzate parti di ricambio non originali Cembre.
Per ordinare parti di ricambio, specifi care sempre i seguenti punti:
- numero di codice del componente
- denominazione del componente
- tipo della testa
- numero di matricola della testa
VAL 130
FIG. 1 CUSTODIE VAL P26
27
Q.tà N° Codice Part. DENOMINAZIONE
1 6340630 15 GRANO CON SFERA M 10
1 6180800 16 DADO M10
1 6100035 17 CHIAVETTA
1 6900250 18 VITE M 5x14
1 6362035 19 GUARNIZIONE PIENA
1 6340082 20 GRANO M 6x8
1 2593864 21 INNESTO Q14-MS COMPLETO
1 6760040 22 SPINA ELASTICA ø 3x8
1 6232006 23 ETICHETTA (TG. 0356)
1 6232061 24 TARGHETTA (TG. 0261)
1
6650118 25 RIVETTO ø 2,5x3,5
1 6620316 PISTONE MONTATO
1 6280026 FORCELLA MONTATA
1 6000075 CONFEZIONE RICAMBIO
VAL 130-U
ITALIANO
Q.tà
2
2
1
1
1
1
1
1
1
1
2